Évaluations - 1, GPA: 4 ( )

Fabricant : Kohler Taille : 2.57 mb Nom Fichier : Langue d'enseignement:

Make sure all union connections to the pump and heater are securely hand tightened. Verify that the pump banding straps have been cut, and that the pump control is resting directly on the subfloor. Ensure that the rubber isolation feet are in place. Fill the whirlpool to a level at least 2.(51 mm) above the top of the highest jet. Operate the whirlpool for 5 minutes (refer to the .Operating Sequence.section) and check all whirlpool piping connections, on the back side, for leaks. Slide the O-Ring onto the first shoulder of the jet. Inspect and lubricate the O-Ring. Insert the jet into the housing, and lightly push and rotate until it snaps in position. Housing Slide the pillow onto the neckjet body. Fit the slip cover over the pillow. Nec kjet Body Install the whirlpool trim kit according to the instructions packed with the trim kit. Pay particular attention to the jet installation steps below -they are very important and are included here to help you obtain smooth, trouble-free jet operation. NOTE:The jet O-ring must be correctly positioned, must be lubricated, and must be in good condition to permit easy rotation and proper operation of the jet. Install the O-ring onto the firstshoulderof the jet. Lubricate the O-ring with silicone lubricant to prevent noisy operation of the jet. Carefully insert the jet into the housing, and lightly push and rotate the jet until it snaps into position. Donotforcethejet. NOTE:When installed correctly, the jet should turn smoothly both clockwise and counterclockwise. 11. Install the Neckjet Pillow (.-N1.Series Only) The whirlpool is supplied with one pillow and two slip covers. The pillow includes a built-in magnetic reed switch. The neckjets will not operate unless the pillow is installed. Always use a slip cover to prevent water from spraying from the whirlpool. Choose a slip cover, and fit it over the pillow. Carefully slide the pillow down onto the neckjet body grooves until it is secure. The neckjets are now ready for use. We recommend periodic cleaning of the slip cover. Follow the cleaning instructions on the label attached to the slip cover. 12. Test Run the Whirlpool Check all electrical connections, and make sure the electrical power to the whirlpool is turned on. Make sure all union connections to the pump and heater are securely hand tightened. Verify that the pump banding straps have been cut, and that the pump control is resting directly on the subfloor. Ensure that the rubber isolation feet are in place. Fill the whirlpool to a level at least 2.(51 mm) above the top of the highest jet. Operate the whirlpool for 5 minutes (refer to the .Operating Sequence.section) and check all whirlpool piping connections, on the back side, for leaks. Slide the O-Ring onto the first shoulder of the jet. Inspect and lubricate the O-Ring. Insert the jet into the housing, and lightly push and rotate until it snaps in position. Housing Slide the pillow onto the neckjet body. Fit the slip cover over the pillow. Nec kjet Body Kohler Co. 11 1019749-2-M Test Run the Whirlpool (cont.) Turn on each of the whirlpool features and verify proper function. Check for any water leakage on the whirlpool’s back side. For additional information on whirlpool operation, see .Confirm Proper Operation. section. 1019749-2-M 12 Kohler Co. 13. Install the Optional Apron To install an optional apron, refer to the installation instructions included with the apron. Install this apron now, before the finished floor and wall materials are completed. 14. Complete the Finished Wall/Deck If you have not already done so, carefully remove the protective tape from the whirlpool rim. Cover the framing with water-resistant wall/deck material. Seal the joints between the whirlpool rim edg...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :