Évaluations - 5, GPA: 3.6 ( )

Fabricant : Image Taille : 683.46 kb Nom Fichier : Langue d'enseignement:

Re-attach the Long Access Panel (5). Remove the two warning decals (not shown) from the spa shell. Using a damp cloth, wipe the spa shell clean. Before filling the spa, make sure that it is in the desired position and that there is room to easily service the spa. Once the spa is filled, it will have to be drained before it can be moved. Using a garden hose or other clean water source, fill the spa. Do not use soft water. The spa may be filled with cold water; however, if warm or hot water is used, the spa will be ready for use sooner. Fill the spa until the water is at the middle of the skimmer opening. Do not overfill the spa. Refer to the inset drawing. Set the Filter (16) into the filter housing. Next, screw the Filter Cover (8) into the filter housing until it is fully seated. 6. Pull down one of the straps on the Spa Cover (11) and hold the Buckle (30) against one of the cedar panels on the spa. (Note: To position the Buckle correctly, have a second person hold the strap on the opposite side of the Spa Cover tight.) The Spa Cover must be tight. Do not place the Buckle over the grooves between the cedar slats. Refer to the inset drawing. Remove the latch from the Buckle (30). Attach the Buckle to the cedar panel with two #4 x 3/4” Screws (31). Attach the other three Buckles (30) to the cedar panels in the same way. Remove the Spa Cover (11) from the spa. 5 Fill to the middle of the Skimmer Housing Filter Housing 6 11 30 Strap Latch 30 31 8 Filter Housing 16 Strap 9 Using the Hydrotherapy Spa The hydrotherapy spa is designed to seat five adults. The spa holds 295 gallons of water and offers a heating system (80°F to 104°F), a filtration system, and adjustable hydrotherapy jets. Follow the guidelines below to use and maintain the spa for your long-term enjoyment. WIRING THE HYDROTHERAPY SPA The hydrotherapy spa is designed to operate with a 240-volt power source. It must be wired directly into a grounded circuit with a Ground Fault Circuit Interrupter (GFCI) capable of carrying 40 amps. No other appliance should be on the same circuit. Connection of the spa to the 240-volt power source must be performed by a qualified, licensed electrician and must comply with all local, state, and federal electrical codes. Please refer to the instructions on the inside of the electronics package for information about connecting the spa to a 240-volt power source. Once the spa is filled with water, the power can be turned on. Note: The first time the power is turned on, the spa will start automatically. TESTING AND TREATING THE WATER The first time you use the spa, you should test and treat the water. You must also treat the water each time you refill the spa. A test strip and a chemical pack are available at your local pool and spa supplier. Follow the directions carefully on the chemical pack to test and treat the water. Always keep the chemicals away from children and pets. See WATER CHEMISTRY on page 14 for information concerning proper water maintenance. STARTING THE HYDROTHERAPY SPA You should always test the GFCI before using the hydrotherapy spa. First, turn on the spa by pressing the jet button on the console (see USING THE CONTROLS on page 12). Once the spa is running, press the GFCI “test” button. The spa should shut off. Press the “reset” button. The spa should resume normal operation. If the spa continues to run after the “test” button is pressed, the GFCI is damaged. Do not use the spa until the GFCI has been repaired or replaced by a qualified electrician. Once you have tested the GFCI, you should verify the water flow from the pumping unit. Set the air control on the console to the lowest setting (see USING THE CONTROLS on page 12). The pumping unit will heat the water as it pumps. Cover the hydrotherapy spa with the spa cover. The spa cover must be tight (see SECURING THE SPA COVER ON THE SPA on this page). The water will heat at about 6°F per hour with the cover on. If you are using the spa indoors, and the room temperature is maintained at 70°F, it will take approximately 6 to 8 hours for the water to reach the set temperature. The temperature and the water flow can be set or changed with the controls on the console (see USING THE CONTROLS on page 12). SECURING THE SPA COVER ON THE SPA To secure the spa cover, snap the latches on the spa cover into the buckles on the cedar panels. To lock the buckles, insert the key and turn it clockwise 1/4 turn. To unlock the buckles, insert the key and turn it counterclockwise 1/4 turn. Always keep the buckles locked when the spa is not in use. Keep the keys in a safe place, out of the reach of children. Latch Key Buckle 10 A. The seven adjustable, directional jets can be pivoted to direct their water flow. B. The adjustable, pulsing jet produces a soothing, pulsating massage action. C. The large rotary jet features two jets of water that provide a pulsating, spinning massage action. D. The six whirly jets provide a continuous whirling massage action. E. The volcano ...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :