Fabricant : Vanguard
Taille : 1.87 mb
Nom Fichier : 110150-01B.pdf
|
Facilité d'utilisation
IMPORTANT: Make sure log does not cover any burner ports (see Figure 25, page 14). WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury. INSTALLING LOGS CAUTION: Do not remove the warning and instruction labels attached to the heater base assembly. These markings contain important warranty and safety information. Figure 24 - Installing One Piece Log Set OFFPILOTON HI LO Chassis "U"-shaped Cutout in Chassis One Piece Log Set Burner Middle Section at Bottom of Log Set INSTALLATION Checking Gas Connections (Cont.) Installing Logs 14 14 INSTALLATION Installing Logs (Cont.) Optional Wireless Hand-Held Remote Control Accessories INSTALLATION Continued 2. Install fireplace insert screen by slipping notches of fireplace insert screen over screws on front of fireplace insert (see Figure 26). WARNING: You must operate this fireplace insert with the fireplace insert screen in place. Make sure fireplace insert screen is in place before running fireplace insert. One Piece Log Set Burner Ports Figure 25 - Installing One Piece Log Set (Top View) Notches Figure 26 - Installing Fireplace Insert Screen Screws for Mounting Screen OPTIONAL WIRELESS HAND-HELD REMOTE CONTROL ACCESSORIES (GHRC and GHRCTA) Installing Remote Receiver Unit 1. Disconnect switch wires from the control valve. 2. Remove screws attaching switch plate. 3. Remove switch plate (see Figure 27). Discard after removing. 4. Install remote receiver unit onto gas log heater base using mounting clips. 5. Push clips firmly into place (see Figure 28). 6. Connect wires as shown in Figure 29. Figure 27 - Switch Plate and Wiring Harness Screw Switch Plate Wires Remote Switch Bracket Ignitor Mounting Clips Remote Receiver Figure 28 - Installing Remote Receiver Valve White Wire From Receiver Red Wire From Receiver Figure 29 - Connecting Wires For more information, visit more information, visit 110150-01B INSTALLATION Installing 9-Volt Batteries OPERATING FIREPLACE INSERT For Your Safety Read Before Lighting Lighting Instructions 15 INSTALLATION Continued INSTALLING 9-VOLT BATTERIES Two 9-volt batteries (not included) are required to operate this heater with the wireless hand-held remote control set. Install one battery in the receiver and one in the hand-held remote control unit. Note:Only use alkaline batteries. Installing 9-Volt Battery (Not Included) in Receiver 1. Locate back of receiver under front burner of heater. 2. Locate the battery clip mounted on the back of the receiver. 3. Slide a 9-volt battery through the clip. 4. Attach the terminal wires to the battery. Remote Terminal Receiver Wires Battery Clip 9-Volt Battery Figure 30 - Installing Battery in Remote Receiver Installing 9-Volt Battery (Not Included) in Hand- Held Remote Control Unit 1. Remove battery cover on back of remote control unit. 2. Attach terminal wires to the battery. Place battery into the battery housing. 3. Replace battery cover onto remote control unit. Model Model GHRCTA Battery CoverTerminal Wires Remote Control Unit 9-Volt Battery Battery Housing GHRC OPERATING FIREPLACE INSERT FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electric switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician or gas supplier. Force or attempted repair may result in a fire or explosion. D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. LIGHTING INSTRUCTIONS WARNING: You must operate this heater with the fireplace insert screen in place. Make sure fireplace insert screen is installed before running fireplace insert. NOTICE: During initial operation of new fireplace insert, burning logs will give off a paper-burning smell. Open damper or window to vent smell. This will only last a few hours. 1. STOP! Read the safety information above. 2. Make sure equipment shutoff valve is fully open. 3. Set switch to OFF position. WARNING: ...
Ce manuel est également adapté pour les modèles :Autres accessoires pour la maison - VI33NRA (1.87 mb)