Évaluations - 1, GPA: 3 ( )

Fabricant : Unigreen Taille : 1.39 mb Nom Fichier : GB_manual_Atomizzatori_P.pdf Langue d'enseignement:

: Depending on the season the vegetation may be more or less luxuriant; bear this in mind before starting the treatment. If the plants don’t have much foliage you should diminish the quantity of litres per hectare using lower pressures or closing one or more jets of the fan. 6.4 CALIBRATING CANNON ATOMISERS ( Tables on pages 31-33 ) Atomisers with a cannon blower group are mainly intended for treating forest trees or other tall plants that it is impossible to drive into with the sprayer (for example tobacco or similar cultivations).They are also frequently used in cultivation under mobile greenhouses. When shooting the atomised chemical mix at distances, that can even be over 40 m, it isn’t possible to verify with the exact distribution on the area treated. Due to the effect of the wind, the presence of turbulence and the obstacle of the same plants being treated, we don’t recommend using cannons with chemical products that need to be distributed with great precision. Don’t use herbicides or similar products. 6.4.1 TREATMENTS ON TALL PLANTS a) Use the tables of pages 31-33 choosing the one relevant to the type of cannon to use and the number of jets. b) On the last line choose the delivery in L/minute that goes with the chosen working pressure. c) Then spray the litres desired on the plant defining the necessary treatment time. When treating a poplar grove or in similar situation there are photocells for the automatic management of the opening of the jet in the presence of the plant to treat, available on request. 20 unigreen 6.4.2 TREATMENTS ON HERBACEOUS CULTIVATIONS a) Use the tables of pages 31-33 choosing the one relevant to the type of cannon to use and the number of jets. b) Find the range and the diameter of the nozzles used (ceramic plate or TR nozzles). c) In the horizontal strip, choose the working speed and the distribution in litres/hectare and on the vertical scale find the pressure to use. d) Adjust the pressure to obtain the treatment required. Note: the minimum range indicated in the table can vary significantly according to the adjustment of the single jets (screwed in more or less). To verify the exact delivery of the fan do tests with clean water. 7 HAND LANCES When using hand lances bear in mind the following notes: = Don’t direct the jet of liquid towards electric power lines or zones where there is electrical current, houses or where people might pass. = Don’t point the jet at people or animals. The jet can cause serious injuries simply due to the mechanical force of the liquid under pressure. = Never block the spraying lever of the lance in an open position because if the lance falls it will be uncontrollable. = At the end of work after you have stopped the pump, make sure that any residual pressure in the pipes under pressure has been drained to avoid unexpected jets when putting the lance away. There are various types of lances; with a lever, mitra spray gun and pistol grip. For further information please refer to the handbook in the package. The lever lance is controlled by opening lever A which, depending on how much it’s pressed, produces a conical spray or direct jet.The standard nozzle is O 1.5 The mitra spray gun can produce a direct jet or a conical spray and the type of spray is selected by pushing lever B forwards or backwards. Use lever C to open the jet.The standard nozzle is O 2.5 Replacement nozzles are available for all of the lances and the capacities are indicated in the tables TAB.4 and TAB.5 ( page 34). A CB unigreen 21 8 MAINTENANCE All of the maintenance operations and repairs must be carried out with the machine and cardan shaft stopped and the tank and circuit clean of any residues of chemical products. The maintenance of the atomiser is essential for maintaining a high level of safety. Also consult the single handbooks of the main components of the atomiser. 8.1 PROGRAMMED MAINTENANCE (TAB. N° 7, page 36) We recommend using a table of programmed maintenance to follow in time to keep the atomiser in an efficient working condition. For major and important maintenance jobs we recommend using the normal UNIGREEN assistance service available from your reseller, (if necessary) replacing parts using original spare parts only. 8.2 ROUTINE MAINTENANCE = After every treatment wash the inside of the tank and the entire circuit as indicated in paragraph 4.13 = Periodically check that the suction and delivery filters are clean = Check the oil level in the volumetric compensator of the pump = The use of chemical products that are particularly damaging for a nitrile rubber mix can cause the diaphragm to break before time. In these conditions check the state of the components more often.There are diaphragms made of special materials (viton and desmopan) that are available on request. = When doing treatments with copper hydroxide you should take great care to thoroughly clean the system, washing it after each treatment because hydroxides attack parts that aren’t painted or pr...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :