Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
Optional end panels are available for corner or one wall installation and are only available at the time of tub order. One Wall Installation - Two Wall Installation - Three Wall Installation - Wall Mount Corner Mount Recess Mount FIGURE 2.1 Tub and surrounding wall configurations Recessed Side Entry Bath Tubs 14 Part No 1150695 SECTION 2—PARTS AND INSTALLATION Installing the Tub WARNING Protective eye wear MUST be worn when drilling to avoid possible eye injury. The tub MUST be supported by the floor and not the deck. NOTE: For this procedure, refer to FIGURE 2.2, FIGURE 2.3 on page 16 and FIGURE 2.4 on page 16. 1. Carefully remove the tub from the carton. 2. Inspect the tub for shipping damage or factory defects. If damage is found, contact the shipping carrier. 3. Measure the tub. 4. Ensure the floor of the installation location will support the tub. 5. Determine whether the unit will be built against one, two or three walls. NOTE: Follow recommended floor plan when installing tub FIGURE 2.4. 6. Three wall installation only .Ensure a stud wall “pocket” has been constructed to receive the tub unit. NOTE: If desired, a wooden nailer may beattached to stud walls as an additional mounting fixture for the tub. NOTE: The opening of the “pocket” should besized to allow the unit to slide in easily, withoutany binding between the studs and the tubunit. Minor gaps will be covered by drywall orpaneling during the finishing stage. Inremodeling situations where tub/shower unitshave been removed, it may be necessary tomodify the opening to receive the tub. FIGURE 2.2 Stud Wall “Pocket” 7. Temporarily slide the unit into place. 8. Mark the location of the fiberglass lip against the studs. 9. Mount 2.inch x 2.inch cleats approximately 1/8.inch below the marks made in STEP 8. 10. Ensure the cleats to not interfere with any components of the unit or restrict installation in any way. 11. Ensure the plumbing and electrical lines have been routed to the proper location. 12. Ensure the unit is level and plumb. NOTE: Use a 4.foot level to level the tub from front to back and side to side. Part No 1150695 15 Recessed Side Entry Bath Tubs SECTION 2—PARTS AND INSTALLATION 13. Model 3750 Only .Perform the following steps to install the shower wand: A. Determine the mounting location for the shower wand and mark this on the wall. NOTE: A shower wand, shower hose, supply elbows, hanger pegs and a flexible supply linehave been supplied with the tub. B. Plumb the supply line to the diverted output port of the mix valve. C. Route the supply line behind the back wall to the location of your choice. D. Drill a hole in the wall to accommodate the plastic compression fitting on the back and the chrome elbow on the front. NOTE: It is advisable to “hard plumb” the shower supply elbow using standard copper pipeand brass fittings strapped to the studs behind the drywall or paneling. Shower Supply Line FIGURE 2.3 Shower Wand Plumbing (Model 3750 Only) 14. Install a service access panel (minimum 16 x 14.inches) on the wall (the back wall orright wall) to allow the pump and controls to be serviced. Top View Front View Model 3750 - Hot and Cold Water Stubs On This End A B B Model 3800 - Hot and Cold Water Stubs C On This End Motor Pump Hookup On This End D E LETTER DESCRIPTION LENGTH IN INCHES A Door Swing Clearance 40 minimum (60 for wheelchair or lift access) B Length of Tub 59.5 C Tub Width 31.5 D Tub Height 41.5 E Seat Height 19 FIGURE 2.4 Installing the Tub Recessed Side Entry Bath Tubs 16 Part No 1150695 SECTION 2—PARTS AND INSTALLATION Electrical and Plumbing Hook-up Locations on the Tub NOTE: For this procedure, refer to FIGURE 2.5 on page 17. NOTE: For installation details refer to Electrical Installation on page 18 and Plumbing Installation on page 20. Front Top View View D ABC FG H NOTE: Model 3750 shown. E LETTER DESCRIPTION MODEL 3750 DIMENSIONS IN INCHES MODEL 3800 DIMENSIONS IN INCHES A Height of Motor (Electrical) Input (115V AC, 60 Hz, 15A) 18 18 B Height of .-inch Hot Water Stub with Recommended Shut Off Valve 31 31 C Height of .-inch Cold Water Stub with Recommended Shut Off Valve 34 34 D Height of 2-inch Drain Pipe (Center) from Floor 5.25 5.25 E Distance of End of 2-inch Drain Pipe from Right End of Tub 20 15 F Distance of Motor Input (115V AC, 60 Hz, 15A) from Front of Tub 7 7 G Distance of .-inch Hot and Cold Water Stubs with Recommended Shut Off Valves from Front of Tub 8 8 H Distance of End of 2-inch Drain Pipe from Front of Tub 21.5 17 FIGURE 2.5 Electrical and Plumbing Hook-up Locations on the Tub Part No 1150695 17 Recessed Side Entry Bath Tubs SECTION 2—PARTS AND INSTALLATION Electrical Installation DANGER When using electrical products, basic precautions should always be followed, including the following: RISK OF ELECTRIC SHOCK. Connect the bathtub only to a circuit protected by a ground-fault circuit-interrupter (GFCI). Use a 15 AMP GFCI breaker only. The National Electric Code requires the use of a ground fault cir...
Ce manuel est également adapté pour les modèles :Autres accessoires pour la maison - 3800 (966.83 kb)