Évaluations - , GPA:
(
)
)
Fabricant : Stovax
Taille : 566.96 kb
Nom Fichier : 2e66bbd8-6bb1-c144-d121-13e142b1d4f5.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
For ventilation requirements in the Republic of Ireland, it will be necessary to refer to the relevant rules in force. AIR VENTS MUST NOT BE RESTRICTED. 11 INSTALLATION INSTRUCTIONS INSTALLATION 1. UNPACKING 1.1 Remove the appliance from its packaging, and check that it is complete and undamaged. 1.2 Put the loose ceramic parts to one side so that they are not damaged during installation. 2. CONTROL UPGRADE 2.1 Your fire is fitted with a control valve that can be easily upgraded to battery powered remote control. This upgrade can be fitted by anyone capable of simple DIY jobs and requires no special training. This upgrade can be obtained through your local Gazco stockist. 2.2 STANDARD REMOTE CONTROL This remote control can control the fire after the pilot has been lit. It can turn the main burner on and regulate it from low through to high and back again. It can turn the main burner off leaving the pilot burning. GAZCO PART NUMBER 8455. 3. SAFETY PRECAUTIONS 3.1 This appliance must be installed in accordance with the rules in force, and used only in a sufficiently ventilated space. Please read all instructions before installation and use of this appliance. 3.2 These instructions must be left intact with the user. 3.3 Do not attempt to burn rubbish on this appliance. 3.4 In your own interest, and those of safety, this appliance must be installed by a competent person in accordance with local and national codes of practice. Failure to install the appliance correctly could lead to prosecution. 3.5 Keep all plastic bags away from young children. 4. INSTALLATION OF THE GAS SUPPLY NATURAL GAS @ 20mbar BUTANE @ 29mbar PROPANE @ 37mbar 8306MCUC 8306PCUC P8306MCUC P8308MCUC 8308MCUC 8308PBUC P8308MCUC P8308PBUC TO CHANGE FROM ONE GAS TYPE TO ANOTHER A COMPLETE ENGINE ASSEMBLY WILL BE REQUIRED. SEE SECTION 8 SERVICING INSTRUCTIONS. 4.1 Before installation, ensure that the local distribution conditions (identification of the type of gas and pressure) and the adjustment of the appliance are compatible. See table above. 4.2 Ensure that the gas supply is capable of delivering the required amount of gas, and is in accordance with the rules in force. Please refer to the technical specification for the correct working pressure for the gas used. 4.3 Soft copper tubing and soft soldered joints can be used but must not be closer than 50mm (2”) to the underside of the burner. 4.4 An isolation device is provided with the appliance. 4.5 All supply gas pipes must be purged of any debris that may have entered, prior to connection to the appliance. 5. PREPARING THE APPLIANCE 5.1 Remove the 6 burner retaining screws and withdraw the burner unit from its location. See diagram 1, arrows B 1AR1175 5.2 Decide on the retention method. If cable fixings are to be used, remove the two knockout holes on the rear of the box, using a sharp hammer blow. See diagram 2. 2 AR1154 5.3 Remove the backing from the self-adhesive silicone sealing strip and apply to the rear flange of the firebox ensuring that it is positioned as close to the outer edge as is practically possible. See diagram 3. 12 3 AR1154 5.4 Gas pipe entry must come through the right hand side of the box. The rubber seal must be cut using a sharp knife to allow the isolating elbow to pass through it. Ensure the rubber is not damaged when doing this. A means of isolation is provided with the appliance. This must be fitted to the supply pipe prior to installing the firebox. 6.INSTALLATION OF THE APPLIANCE 6.1 Ensure that the fireplace opening is in compliance with the requirements of section 2 Site Requirements then proceed as follows: A) CABLE RETENTION METHOD 6.2 Mark the position of the 4 fixing holes on the rear of the fireplace opening and drill the holes using a No. 12 masonry drill bit. Insert the 4 fibre rawl plugs and screw the eyebolts in as far as possible leaving the eye horizontal. See diagram 4. 4 AR1205 AR1204HotboxConvector757575754654832824 6.3 Pass the 2 cables through the holes in the bracket on the back of the firebox and pull taut so that the stop ends sit tightly against the top of the bracket. See diagram 5. 5 AR1155 AR1156HotboxConvector 6.4 Pass the cables vertically through the 2 sets of eyebolts and thread the ends through the holes in the lower back of the firebox. Pass the gas supply pipe through the hole in the rubber seal (refer to section 5.2) and push the appliance into place. 6.5 Thread the cables through the tensioner bolts and push the threaded portions through the holes in the firebox so that the lock nut sits against the back wall (ensure that the nut is screwed fully up to the head of the tensioner to allow maximum adjustment). 6.6 Slide the locking nipples onto the cables, pull the cables taut and tighten the locking screw. Adjust the lock nuts using a 10mm spanner until the silicone sealing strip forms a tight seal between the fireplace opening and the firebox flange. See diagram 6. 6 AR1157 6.7 Coil up the surplus cable and locate in the back of...