Évaluations - 2, GPA: 5
(
)
)
|
Facilité d'utilisation
JET Equipment & Tools reserves the right to effect, at any time and without prior notice, changes or alterations to parts, fittings, and accessory equipment deemed necessary for any reason whatsoever. 7 A WARNING Read and understand the entire contents of this manual before attempting assembly or operation of the dust collector! Failure to comply may cause serious injury! Unpacking 1. Finish removing all contents from the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembled and is running properly. Contents of the Shipping Carton 1 Bag Hanger 1 Base 1 Housing 1 Hanger Bracket 1 Hose 1 Owner's Manual 1 Warranty Card 1 Motor/Fan Assembly 1 Collector Bag 1 Filter Bag 2 Hose Clamps 1 Retainer Strap 4 Casters 1 Inlet Cover & Hose Inlet 3 Support Legs 1 Bag of Assembly Hardware 16. M8 x 16 Hex Cap Bolts 22. M8 Flat Washers 8. M6 x 12 Pan Head Flange Bolts 6. M8 Hex Nuts Tools Required for Assembly 2. 1/2” or 13mm Wrenches or sockets 1. 9/16” or 14mm Wrench or socket 1. #2 Cross Point Screw Driver JET 22) M8 Flat Washers 6) M8 Hex Nuts 16) M8 x 16 Hex Cap Bolts 8) M6 x 12 Pan Head Flange Bolts 8 Assembly 1. Install four casters to the under side of the base as pictured in Fig. 1. Thread the hex nut (B, Fig. 1) onto the caster shaft. Then slide the lock washer (A, Fig. 1) over the caster shaft. Thread the caster shaft into the threaded hole on the underside of the base, turn until snug. Tighten the nut (B, Fig. 1) against the base with a 9/16” or 14mm wrench. This will give the caster proper clearance. 2. Place the base with casters on the ground. Attach the motor and fan assembly (A, Fig. 2) to the base using four M8 x 16 hex cap bolts, four M8 flat washers (B, Fig. 2), and a 1/2" or 13mm wrench. A WARNING The dust collector must be disconnected from the power source during assembly. Failure to comply may result in serious _injury!_ 3. Attach inlet guard (A, Fig. 3) to fan housing using eight M5 x 12 pan head screws (B, Fig. 3). Press the inlet ports onto the inlet guard until it snaps into place. A WARNING To reduce the risk of injury from moving parts, always keep inlet ports covered with the caps provided, if they are not connected to a flexible hose. Failure to comply may result in serious injury! 9 4. Attach three support brackets (A, Fig. 4) to the base using six M8 x 16 hex cap bolts and six M8 flat washers (B, Fig. 4). Hand tighten only at this time. 5. Install the housing (A, Fig. 5) to two support brackets using four M8 x 16 hex cap bolts, eight M8 flat washers, and four M8 hex nuts (B, Fig.5). Be sure hose opening faces fan housing. Before attaching third support bracket place the hanger bracket (C, Fig.5) between the support bracket and the housing. Tighten all nuts and bolts at this time with a 1/2" or 13mm wrench. 6. Attach the hose (A, Fig. 6) between the fan housing and the collector housing with two clamps (B, Fig. 6). Tighten the clamps to secure the hose. # * * Fig. 4 Fie. S Fig. 6 10 7. Slide the bag hanger hook (A, Fig. 7) through the top loop of the filter bag. Insert the hanger into the hanger bracket. Thread the retainer strap (B, Fig. 7) through the loops on the filter bag (C, Fig.7), and fasten to the collector housing. The retainer strap should be tight enough to provide a good seal. 8. Insert the ring (A, Fig. 8) of the collector bag into the bottom of the housing at an angle. Pull down on the bag to make sure it “seats” in the housing. Electrical Connections A WARNING All electrical connections must be done by a qualified electrician. All adjustments or repairs must be done with the dust collector disconnected from the power source, unplugged. Failure to comply may result in _serious injury!_ The DC-1100A dust collector is rated at 115/230V, Prewired 115V. Use a plug and outlet rated at least 20 amps. The circuit for the machine should also be protected by at least a 20 amp circuit breaker or fuse. Keep in mind that a curcuit being used by other machines, tools, lights, heaters, etc. at the same time will add to the electrical load. A dedicated curcuit to the dust collector will give you the best results since dust collectors are generally used at the same time other tools are running. Before hooking up to the power source, make sure that the switch is in the off position. Turning the Machine On & Off Before hooking up to the power source, make sure that the switch is in the off position. The dust collector can be turned on by pressing the start button found on the motor. Press the stop button to turn off the dust collector. JET (gUI&MEMT ft TQQ15 Fig. a 11 Maintenance A WARNING Never perform maintenace on this machine before turning switch off and removing plug from power source, unplug. Failure to comply may cause serious injury! Cleaning the Filter Bag A CAUTION Wearing a particle mask/respirator for protection against fine...