Évaluations - 2, GPA: 3
(
)
)
|
Facilité d'utilisation
Use this and other machinery with caution and respect. Failure to do so could result in serious personal injury, damage to equipment, or poor work results. -8- G5954 5HP Dust Collector SECTION 2: CIRCUIT REQUIREMENTS 220V Single-Phase ▲WARNING Serious personal injury could occur if you connect the machine to the power source before you have completed the set up process. DO NOT connect the machine to the power source until instructed to do so. Amperage Draw The Model G5954 motor draws the following amps under maximum load: Motor Draw at 220V..............................34 Amps Circuit Requirements We recommend using a dedicated circuit for this machine. You MUST connect your machine to a grounded circuit that is rated for the amperage given below. Never replace a circuit breaker on an existing circuit with one of higher amperage without consulting a qualified electrician to ensure compliance with wiring codes. If you are unsure about the wiring codes in your area or you plan to connect your machine to a shared circuit, consult a qualified electrician. 220V Circuit...........................................50 Amps Connection Type (Figure 1) 220V.............................Locking Shut-off Switch Grounding In the event of an electrical short, grounding reduces the risk of electric shock. The grounding wire in the power cord must be properly connected to the grounding pole in the locking shut-off switch; likewise, the locking shut-off switch must be properly installed and grounded. All electrical connections must be made in accordance with local codes and ordinances. Jt ▲WARNING Electrocution or fire could -7 result if this machine is not grounded correctly or if your electrical configuration does not comply with local and state codes. Ensure compliance by checking with a qualified electrician! G5954 5HP Dust Collector -9- SECTION 3: SET UP Inventory After all the parts have been removed from the two boxes, you should have the following items: Large Component Inventory (Figure 2) Qty A. Casters (shown attached to base plate) .... 4 B. Base Plate..................................................1 C. Motor/Fan Assembly..................................1 D. Stand Legs ................................................. 4 E. Collector.....................................................1 Small Component Inventory (Figure 3) Qty F. Gasket ........................................................ 1 G. 4-in-1 Inlet Adapter and Inlet Caps............1 H. Upper Bag Support Extenders...................2 I. Lower Support............................................1 J. Upper Bag Supports...................................2 K. Plastic Elbows 4" 90°.................................2 L. Lower Bags................................................2 M. Upper Bags................................................2 Other Components and Hardware Qty • Flange Bolts 3/8-16 x V2" (A, B, C, D)........32 • Washers 3/8" (D, E)...................................16 • Hex Nuts %-16 (C, E, F)............................8 • Hex Bolts 3/8-16 x 11/4" C, E, F)...................8 • Flange Bolts 5/16-18 x 3/4" (I, J) ...................6 • Hex Nut 5/8-11 (I).........................................1 • Flange Bolts V4-20 x V2" (H, J)...................4 • Lower Support Foot Pad 5/8-11...................1 • Open-End Wrench 10/12mm......................1 • Bag Clamps................................................4 Figure 2. G5954 Large Component Inventory. Figure 3. G5954 Small Component Inventory. In the event that any nonproprietary parts are missing (e.g. a nut or a washer), we would be glad to replace them, or for the sake of expediency, replacements can be obtained at your local hardware store. NOTICE Some hardware/fasteners on the inventory list may arrive pre-installed on the machine. Check these locations before assuming that any items from the inventory list are missing. 10- G5954 5HP Dust Collector Cleaning Site Considerations When cleaning, avoid chlorine-based solvents, such as acetone or brake parts cleaner, as they may damage painted surfaces should they come in contact. Always follow the manufacturer’s instructions when using any type of cleaning product. ▲WARNING Gasoline and petroleum products have low flash points and could cause an explosion or fire if used to clean machinery. DO NOT use gasoline or petroleum products to clean the machinery. ▲CAUTION Many of the solvents commonly used to clean machinery can be toxic when inhaled or ingested. Lack of ventilation while using these solvents could cause serious personal health risks or fire. Take precautions from this hazard by only using cleaning solvents in a well ventilated area. Working Clearances Consider existing and anticipated service/mainenance needs, size of material to be processed through each machine, and space for auxiliary stands, work tables or other machinery when establishing a location for your new mach...