Évaluations - , GPA:
(
)
)
Fabricant : Chief Manufacturing
Taille : 68.94 kb
Nom Fichier : d2f820ea-6ef0-4acc-876a-5ec1b02e9884.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
WARNING Be aware of the potential for personal injury or damage to the equipment if it is not adequately mounted. WARNING The installer is responsible for verifying that the mounting surface to which the CTA-111 is anchored will safely support the combined load of all attached components or other equipment. WARNING The combined weight of the TV/monitor and all attached components and equipment placed on the CTA-111 must not exceed 300 lbs. (136.1 kg), the maximum weight capacity of the CTA-111. WARNING Watch for pinch points. Do not put your fingers between movable parts. CAUTION Check the unit for shipping damage before you begin the installation. Installation Instructions CTA-111 CONTENTS INSPECT THE UNIT BEFORE INSTALLING ............. 3 PARTS .......................................................................... 3 TOOLS REQUIRED FOR INSTALLATION................. 4 INSTRUCTIONS........................................................... 4 Installing Top Stud Spanning Adapter to Wall ............ 4 Attaching Stud Spanning Adapter to Wall Arm........... 5 Attaching Wall Arm to Wall-Mounted Top Stud Spanning Adapter ....................................................... 5 Attaching Bottom Stud Spanning Adapter to Wall ...... 6 Attaching Front Cover ................................................ 6 Connecting NPT Pipe or Nipple to Wall Arm.............. 6 INSPECT THE UNIT BEFORE INSTALLING Unpack the carton. Carefully inspect the parts for shipping damage. Verify contents listed in Table 1. If you are missing any of the listed parts, contact Customer Service at: 1-800/582-6480.300. Table 1. Shipping Contents ITEM DESCRIPTION QTY 10 16” Spanning Adapter 2 20 5/16 X 2.5” Lag Bolt 4 30 5/16 Flat Washer 4 40 M8 Flat Washer 6 50 M8 Lock Washer 6 60 M8 Hex Nut 6 PARTS 10 40 50 60 20 30 Figure 1. CTA-111 Parts Installation Instructions CTA-111 4 TOOLS REQUIRED FOR INSTALLATION The tools required for installation are as follows: .. Electric drill and bit set .. Stud sensor (mechanical or electronic) .. .” box-end wrench or ratchet with .” socket .. 13mm box-end wrench or ratchet with 13mm socket .. Level NOTE: Other tools may be required depending on your method of installation. Figure 2. Install Stud Spanning Adapters INSTRUCTIONS STEP 1 Installing Top Stud Spanning Adapter to Wall Install the top 16” stud-spanning adapter, as follows: NOTE: The top and bottom stud-spanning adapters must be mounted to wood studs that are 16” apart on center. See Figure 2. 1. Locate the two 16” stud-spanning adapters (10), four lag bolts (20), and four flat washers (30). WARNING It is the installer’s responsibility to verify that the structure to which the mount is anchored will safely support five times the combined load of all attached components and equipment. 2. Determine a suitable mounting location. Keep in mind that both stud-spanning adapters (10) must be mounted to wood studs that are 16” apart on center. 3. Using a stud sensor, locate the two wood studs where you will mount the top stud-spanning adapter (10). 4. Holding the top stud-spanning adapter (10) against the wall, use a pencil, awl, or small nail to mark the mounting holes where two pilot holes will be drilled into the center of the wood studs. Make sure that the mounting holes in the unit are level. 5. Using a 15/64” drill bit, drill two pilot holes for anchoring the top stud-spanning adapter (10). 6. Using two 5/16” lag bolts (20) and two 5/16” flat washers (30), attach the top stud-spanning adapter (10) to the wall. 16” Installation Instructions CTA-111 STEP 2 Attaching Stud Spanning Adapter to Wall Arm NOTE To minimize error, the wall arm is attached to the bottom stud-spanning adapter (10) before the wall arm and bottom stud-spanning adapter are secured to the wall. Refer to CTA-025 Single Stud Wall Arm (8809-000027) document for specific installation instructions to mount the wall arm. 1. Locate the wall arm and its attaching parts [three M8 hex nuts (60), three M8 lock washers (50), Figure 3. Attach Chief Wall Arm to Bottom Stud and three M8 flat washers (40)]. See Figure 3. Spanning Adapter 2. Using the parts listed in step 1, attach the wall arm to the bottom 16” stud-spanning adapter (10). Tighten hex nuts. See Figure 3. Figure 4. Attach Wall Arm to Wall-Mounted Stud Spanning Adapter STEP 3 Attaching Wall Arm to Wall-Mounted Top Stud Spanning Adapter 1. Locate the following attaching parts for the wall arm [three M8 hex nuts (60), three M8 lock washers (50), and three M8 flat washers (40)]. See Figure 4. 2. With an assistant, perform the following steps: a. Lift wall arm onto the top wall-mounted 16” stud-spanning adapter (10). See Figure 4. b. Using the parts listed in step 1, attach the wall arm to the top wall-mounted 16” stud- spanning adapter (10). Tighten hex nuts. Installation Instructions CTA-111 6 STEP 4 Attaching Bottom Stud Spanning Adapter to Wall 1. Using a 15/64” drill bit, drill two pilot holes for anchoring the bottom stud-spanning ad...