Évaluations - 5, GPA: 4.6
(
)
)
|
Facilité d'utilisation
The fan should rotate clockwise. You can reverse the rotation of the motor by interchanging any two of the three incoming power lines connected to terminals (C) Fig. 16. Disconnect the machine from the power source before reversing the wires. ADANGER 460 VOLT OPERATION 460V operation of the 50-762 requires replacement of the motor starter and reconfiguration of the motor's internal connections. This item is available from most industrial electrical supply dealers and must be installed by a qualified electrician. ESZQHMH DO NOT ATTEMPT to wire the machine for 460 volts without replacing the starter. Doing so will cause damage to the machine and personal injury could result. AWARNING AWARNING AWARNING Re-install the cover before operating. Do not insert fingers or any foreign object into the dust intake port. Make sure that the unit is properly grounded. MODEL 50-763 SINGLE PHASE INSTALLATION Your dust collector must be permanently connected to the building's electrical system and grounded to meet code. 1. Remove the controller cover (A) Fig. 17. 2. Bring the single phase power line through the access hole (B) Fig. 17 in the bottom of controller box and connect the two power lines to terminals (E) Fig. 18, and the green ground wire to the ground screw (F). AWARNING AWARNING AWARNING Re-install the cover before operating. Do not insert fingers or any foreign object into the dust intake port. Make sure that the unit is properly grounded. 12 OPERATION STARTING AND STOPPING THE DUST COLLECTOR The on/off buttons (A) and (B) Fig. 19 are located on the front of the motor housing. To turn the machine "ON", push the "ON" button (A). To turn the machine "OFF", push the "OFF" button (B). LOCKING SWITCH IN THE "OFF” POSITION IMPORTANT: When the machine is not in use, the "ON" button (A) Fig. 19 should be locked to prevent unauthorized use, using a padlock (C) Fig. 20 with a 3/16" diameter shackle through the hole beside the button. When using this dust collector, do not pick up anything that is burning, smoldering, or smoking, such as matches, cigarettes, or hot ashes. Do not use this machine to vacuum combustible explosive materials, such as coal, grain, or other finely-divided combustible materials. Do not use this machine to vacuum hazardous, toxic, or carcinogenic materials, such as asbestos, pesticide, or lead-based paint debris. TROUBLESHOOTING For assistance with your machine, visit our website at for a list of service centers or call the DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582). MAINTENANCE KEEP MACHINE CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. ESHUMEI WEAR CERTIFIED SAFETY EQUIPMENT FOR EYE, HEARING AND RESPIRATORY PROTECTION WHILE USING COMPRESSED AIR. FAILURE TO START Should your machine fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line. LUBRICATION & RUST PROTECTION Apply household floor paste wax to the machine table, extension table or other work surface weekly. Or use a commercially available protective product designed for this purpose. Follow the manufacturer's instructions for use and safety. To clean cast iron tables of rust, you will need the following materials: a pushblock from a jointer, a sheet of medium Scotch-Brite™ Blending Hand Pad, a can of WD-40® and a can of degreaser. Apply the WD-40 and polish the table surface with the Scotch-Brite pad using the pushblock as a holddown. Degrease the table, then apply the protective product as described above. 13 SERVICE REPLACEMENT PARTS Use only identical replacement parts. For a parts list or to order parts, visit our website at servicenet.deltamachinery.com. You can also order parts from your nearest factory-owned branch, or by calling our Customer Care Center at 1-800-223-7278 to receive personalized support from highly-trained technicians. SERVICE AND REPAIRS All quality tools will eventually require servicing and/or replacement of parts. For information about Delta Machinery, its factory-owned branches, or an Authorized Warranty Service Center, visit our website at or call our Customer Care Center at 1-800-223-7278. All repairs made by our service centers are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by others. You can also write to us for information at Delta Machinery, 4825 Highway 45 North, Jackson, Tennessee 38305 - Attention: Product Service. Be sure to include all of the information shown on the nameplate of your tool (model number, type, serial number, etc.) ACCESSORIES A complete line of accessories is available from your Delta Supplier, Porter-...
Ce manuel est également adapté pour les modèles :Autres outils - 50-763 (640.03 kb)