Évaluations - 2, GPA: 3
(
)
)
|
Photos et spécifications Makita HR2470FT |
Facilité d'utilisation
Switch action 1. Switch trigger 2. Lock button 2 CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop. For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. 1 Lighting up the lamps For Model HR2470F, 2470FT 1 1. Lamp 007934 CAUTION: • Do not look in the light or see the source of light directly. To turn on the lamp, pull the trigger. Release the trigger to turn it off. NOTE: • Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. Reversing switch action A B 1. Reversing switch lever 1 007935 CAUTION: • Always check the direction of rotation before operation. • Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. • If the switch trigger can not be depressed, check to see that the reversing switch is fully set to position (A side) or (B side). This tool has a reversing switch to change the direction of rotation. Move the reversing switch lever to the position (A side) for clockwise rotation or the position (B side) for counterclockwise rotation. Changing the quick change chuck for SDS-plus For model HR2470T/HR2470FT The quick change chuck for SDS-plus can be easily exchanged for the quick change drill chuck. 4 Removing the quick change chuck for SDS-plus 2 3 Removing the quick change chuck for SDS-plus 2 3 1. Quick change chuck for SDS-plus 2. Change cover line 3. Chain cover 007944 CAUTION: • Before removing the quick change chuck for SDS-plus, always remove the bit. Grasp the change cover of the quick change chuck for SDS-plus and turn in the direction of the arrow until the change cover line moves from the symbol to the symbol. Pull forcefully in the direction of the arrow. Attaching the quick change drill chuck 12 3 4 1. Spindle 2. Quick change drill chuck 3. Change cover line 4. Change cover 007945 Check the line of the quick change drill chuck shows the symbol. Grasp the change cover of the quick change drill chuck and set the line to the symbol. Place the quick change drill chuck on the spindle of the tool. Grasp the change cover of the quick change drill chuck and turn the change cover line to the symbol until a click can clearly be heard. Selecting the action mode Rotation with hammering 12 1. Lock button 2. Action mode changing knob For drilling in concrete, masonry, etc., depress the lock button and rotate the action mode changing knob to the symbol. Use a tungsten-carbide tipped bit. Rotation only 1. Rotation only 1 007947 For drilling in wood, metal or plastic materials, depress the lock button and rotate the action mode changing knob to the symbol. Use a twist drill bit or wood bit. Hammering only 1. Hammering only 1 007948 For chipping, scaling or demolition operations, depress the lock button and rotate the action mode changing knob to the symbol. Use a bull point, cold chisel, scaling chisel, etc. CAUTION: • Do not rotate the action mode changing knob when the tool is running under load. The tool will be damaged. • To avoid rapid wear on the mode change mechanism, be sure that the action mode changing knob is always positively located in one of the three action mode positions. Torque limiter The torque limiter will actuate when a certain torque level is reached. The motor will disengage from the output shaft. When this happens, the bit will stop turning. CAUTION: • As soon as the torque limiter actuates, switch off the tool immediately. This will help prevent premature wear of the tool. • Bits such as hole saw, which tend to pintch or catch easily in the hole, are not appropriate for this tool. This is because they will cause the torque limiter to actuate too frequently. 5 ASSEMBLY ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Side grip (auxiliary handle) 1. Grip base 3 51 6 2. Side grip 3. Loosen 4. Tighten 5. Teeth 6. Protrusion 4 2 007949 CAUTION: • Always use the side grip to ensure operating safety. Install the side grip so that the teeth on the grip fit in between the protrusions on the tool barrel. Then tighten the grip by turning clockwise at the desired position. It may be swung 360° so as to be secured at any position. Bit grease Coat the bit shank head beforehand with a small amount of bit grease (about 0.5 - 1 g). This chuck lubrication assures smooth action and longer service life. Installing or removing the bit 21 1. Bit shank 2. Bit grease Clean the bit shank and apply bit grease before installing the bit. 1. Bit 2. Chuck cover Insert the bit into the tool. Turn th...
Ce manuel est également adapté pour les modèles :Autres outils - HR2470 (1.13 mb)
Autres outils - HR2470F (1.13 mb)