Évaluations - 1, GPA: 4
(
)
)
|
Facilité d'utilisation
Also, give these operating instructions to whoever might acquire the appliance at a future time. Safety instructions Risk of personal injury! • Keep and store the appliance out of the reach of children. This laser appliance contains a Class 2 Laser. NEVER direct the laser beam at people or animals. NEVER look directly into the laser. The laser beam can cause serious eye damage. • Do NOT direct the laser beam at strongly reflective material. Reflected laser beams are also dangerous. • In the event of the batteries leaking acids, wear protective gloves. There is a risk of receiving chemical burns! Beware of appliance damage! • NEVER subject the appliance to rain. Do not use the appliance in wet or moist environments. • Do not use the appliance at locations where there is a danger of fire or explosion, e.g. in the vicinity of inflammable liquids or gases. • All adjustments intended to increase the laser power are forbidden. • To avoid damage to the appliance, arrange for repairs to be carried out only by our Customer Services Department or qualified specialists. • Regularly check the condition of the batteries. Leaking batteries can cause damage to the laser appliance. • If you do not intend to use the laser appliance for an extended period, remove the batteries. • Always change all batteries at the same time and always use batteries of the same type. • Clean the battery compartment with a dry cloth. • No liabilty will be accepted for damage resulting from manipulation to the laser equipment as well as from disregarding these safety instructions. Intended use The appliance is intended for use in making alignments and determining angles in domestic construction work. The appliance is intended for domestic purposes only, not for commercial purposes. Items supplied • Laser appliance with rotating plate • 2 Batteries 1.5 V, Type AAA/LR03 • Operating instructions • Warranty card Technical Data Power supply: 2 Batteries 1.5 V, Type AAA/LR03 Measurement accuracy: ± 6,35 mm over 5 meters Laser class 2 (.5mW, .= 650 nm) - 1- Appliance description q Laser appliance w ON/OFF button e Spirit level for horizontal lines r Spirit level for vertical lines t Laser lens y Rotating plate with degree scale u Marking arrow i Fastening pins o Fixing points on the laser appliance a Fixing points on the rotating plate s Battery compartment (on the rear side) Inserting the batteries 1. Open the battery compartment s. 2. Insert two batteries of Type AAA/LR03 into the battery compartment s. Comply with the polarity markings in the battery compartment s. 3. Close the battery compartment s. Utilisation Switching On and Off 1. To switch the laser appliance q on, press the ON/OFF w button. 2. To switch the laser appliance q off, press the ON/OFF w button once again. Utilisation on a wall 1. Remove the laser appliance q from the rotating plate. The laser appliance clings to the rotating plate y magnetically. 2. Place the rotating plate y at the position on the wall from where you wish to draw the alignment line. 3. Secure the rotating plate y to the wall in that you take both fastening pins i from the sides of the appliance and you press them through the fixing points on the rotating plate a and into the wall (See Fig. ). Notice: The fastening pins i can be inserted into most upper surfaces, such as wood, plaster or mortar. Alternatively, especially with other upper surfaces, you could also use adhesive tape for securing the rotating plate y. You can also secure the laser appliance q without the rotating plate, in that the fastening pins i are inserted through fixing points on the laser appliance o itself. 4. Place the laser appliance q onto the rotating plate y. 5. Turn the laser appliance q with the marking arrow u into the desired direction. 6. Switch the laser appliance q on, by pressing the ON/OFF button w. The laser beam appears on the wall in the direction of the marking arrow u. Plumb-line To mark a plumb-line, turn the laser appliance q on the rotating plate y with the marking arrow u pointing in the direction in which the laser marking is to be indicated, then finely adjust it vertically with the spirit level r. - 2 Horizontal line To mark a horizontal line, turn the laser appliance q on the rotating plate y with the marking arrow u pointing in the direction in which the laser marking is to be indicated, then finely adjust it horizontally with the spirit level e. Important: The air-bubbles in the spirit levels e+r must be positioned between the two markings. Angles 1. To mark an angle, shift the zero marking of the degree scale to the marking arrow u on the laser appliance q (Fig. ). 2. Turn the laser appliance q from the start position (Fig. ) with the marking arrow u to the desired angle (e.g. 45°, Fig. ). Utilisation on the floor/on the ceiling 1. Should you use the laser appliance q on the floor or on the ceiling, secure it as described above if need be. 2. Turn the laser appliance q with the marking arrow u in the desired di...