Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
Further details can be found in the operating instructions. Keep these instructions in a safe place. If you pass the tool on to anyone else, please ensure that you also pass on all the documentation. • Proper use The device is intended for gluing wood, cardboard, packaging, PVC, carpet, seals, plastic, leather, ceramic, glass and textiles with hot-melt adhesive. The material to be glued must be clean, dry and free of grease. Any other use or modification to the tool shall be considered as improper use and could give rise to considerable dangers. The manufacturer will not accept liability for loss or damage arising from improper use. The tool is not intended for commercial use. • Features T Feed channel y Check indicator y Charger connection 4 Charger with stand 5_ Feed switch y Wire stand y Drip tray y Nozzle y Nozzle heat shield 10 Glue gun connection 11 Mains lead • Included items 1 Glue gun PHKP 500 1 Charger with stand 1 Mains lead 1 Wire stand 1 Replacement nozzle (short) 1 Interchangeable nozzle (long) 2 Glue sticks 1 Operating instructions 1 Booklet covering "Warranty and service" GB/MT | B4RK51DE | Introduction / Safety notes • Technical details Nominal voltage: Nominal power (heating-up): Nominal power (working): Heating up time: Protection class: 230 V ~ 50 Hz approx. 500 W approx. 35 W approx. 4 min. II / & PHKP500 KH 3119 230 V ~ 50 Hz-35 W (500 W) \Jß Date of manufacture: 02-2008 Kompemaß GmbH • D- 44867 Bochum ■ Germany • Safety notes Attention! Please read all the instructions and advice. Failure to observe the instructions and advice given below may result in electric shock, fire and / or serious injury. 1. Your working area a) Keep your working area clean and clutter-free. Untidy or poorly lit working areas can lead to accidents. b) Do not allow the device to become wet. Do not operate it in a moist environment. c) mi Keep children and other peo- № ple away while you are operating the electrical tool. Distractions can cause you to lose control of the device. 2. Electrical safety a) The mains plug on the device must match the mains socket. The plug must not be modified in any way. Do not use an adapter plug with devices fitted with a protective earth. Unmodified plugs and matching sockets reduce the risk of electric shock. b) Avoid touching earthed surfaces such as pipes, radiators, ovens and refrig- erators with any part of your body. There is an increased risk of electric shock if your body is earthed. c) Keep the device away from ] rain or moisture. Water entering an electrical device in creases the risk of electric shock. d) Do not use the mains lead for any purpose for which it was not intended, e.g. to carry the device, to hang up the device or to pull the mains plug out of the mains socket. Keep the lead away from heat, oil and sharp edges. Do not touch the mains lead if it becomes damaged or severed while you are working, instead pull the mains plug out of the mains socket immediately. Damaged or tangled mains leads increase the risk of electric shock. e) When working outdoors with an electrical power tool always use extension cables that are also approved for use outdoors. The use of an extension cable suitable for outdoor use reduces the risk of electric shock. 3. Personal safety a) Remain alert at all times, watch what you are doing and always proceed with caution. Do not use the device if you are tired or under the influence of drugs, alcohol or medication. One moment of carelessness when using the device can lead to serious injury. b) To avoid the danger of injury, burning and damage to health: Danger of burns! The glue and the nozzle can reach temperatures of 200 °C. Do not touch the nozzle or the glue. Keep other people and animals away from the hot glue. On contact with the skin, hold the affected part under running cold water for several minutes. Do not try to remove the glue from the skin. A I R4RKSIDE I GB/MT Safety notes / Operation 4. Careful handling and use of electrical power tools a) Pull the mains plug from the socket before you make any adjustments to the device, change accessories or when the device is put away. This precaution is intended to prevent you from unintentionally starting the device. b) When not in use always ensure that electrical power tools are kept out of reach of children. Do not let anyone use the device if he or she is not familiar with it or has not read the instructions and advice. Electrical power tools are dangerous when they are used by inexperienced people. Let the device cool down completely before putting it away. The hot nozzle can cause damage. c) Look after the device carefully. Check that moving parts are working properly and move freely. Check for any parts that are broken or damaged enough to detrimentally affect the functioning of the device. Have damaged parts repaired before you use the device. Many accidents have their origins in poorly m...