Log:
Évaluations - 3, GPA: 4.3 ( )

Instructions IBM, Modèle EGX-600

Fabricant : IBM
Taille : 2.37 mb
Nom Fichier : a7bec66f-799f-41f0-9580-343422d27153.pdf
Langue d'enseignement: enfr
Aller à la télécharger



Facilité d'utilisation


At this screen you can use button operations to move or rotate the spindle. You can decide on the movement destination as you verify the on-screen coordinate values and the actual position. To set the present location of the spindle as the movement destination, press the [ENTER/PAUSE] button. To cancel and return, press the [MENU] button. Detail Screen 2 This displays the X, Y, and Z coordinates of the set movement destination. Use this screen to verify the settings. Chapter 5 - The Teaching Feature 91 5-7. List of Commands 5-7. List of Commands Function This moves the spindle head to the specified X, Y, and Z coordinates, moving all three axes simultaneously (at the specified feed rate). Value . Feed rate (0 to 50 mm/s) Value . X, Y, and Z coordinates for the movement destination Basic Screen .. Z -500 . 8000RPM X 1000 Y 1000 Basic Screen 1: 8 CUT-3 50 to cancel . Basic Screen X 1000 Y 1000 Z -500 Dest. This moves the spindle at the specified feed rate. It moves all three axes simultaneously to the specified X, Y, and Z coordinates. Unlike [CUT-ZM] and [CUT-ZI], it effects linear movement to the specified X, Y, and Z coordinates. This command has no function for rotating or stopping the spindle. Basic Screen Specify the feed rate. Specifying [0] sets a speed of 0.5 mm/s. After you input the speed, press the [ENTER/PAUSE] button to go to the settings at Detail Screen 1. Detail Screen 1 Specify the X, Y, and Z coordinates for the movement destination. At this screen you can use button operations to move or rotate the spindle. You can decide on the movement destination as you verify the on-screen coordinate values and the actual position. To set the present location of the spindle as the movement destination, press the [ENTER/PAUSE] button. To cancel and return, press the [MENU] button. Detail Screen 2 This displays the X, Y, and Z coordinates of the set movement destination. Use this screen to verify the settings. 92 Chapter 5 - The Teaching Feature 5-7. List of Commands 5-7. List of Commands Function This moves the spindle head in an arc. Value . Relative location from the start point to the center of the circle (X and Y coordinates) Value . Angle from the arc start point to end point (-360 to 360 deg.) Value . Resolution (0 to 120 deg.) Value . Feed rate (0 to 50 mm/s) Basic Screen 1: 9 ARC Detail Screen 1 RELATIVE CENTER X 500 Y 500 to cancel Detail Screen 2 SET ANGLE ---> 90 Detail Screen 3 SET TOLERANCE ---> 5 Detail Screen 4 SET SPEED ---> 20 . . . . . to cancel to cancel to cancel Center Start point Angle Y X End point This moves from the present location in an arc of the specified angle. Arc movement is possible only on the X and Y plane. Detail Screen 1 Specify the center of the circle. Specify relative coordinates from the present location, which is the start point. Note that these are not coordinates referenced to the workpiece origin point. To go to Detail Screen 2, press the [ENTER/PAUSE] button. To cancel and return, press the [MENU] button. Detail Screen 2 Specify the angle from the start point to the end point. The direction of turning is determined by whether the value is positive or negative. A positive value yields counterclockwise turning and a negative value yields clockwise turning. To go to Detail Screen 3, press the [ENTER/PAUSE] button. To cancel and return, press the [MENU] button. Detail Screen 3 Specify the resolution (smoothness) of the arc. Smaller values result in greater smoothness, but the apparent feed rate becomes slower. Specifying [0] sets the machine's highest resolution. To go to Detail Screen 4, press the [ENTER/ PAUSE] button. To cancel and return, press the [MENU] button. Detail Screen 4 Specify the feed rate. Specifying [0] sets a speed of 0.5 mm/s. To finish setting the value, press the [ENTER/PAUSE] button. To cancel and return, press the [MENU] button. Chapter 5 - The Teaching Feature 93 5-7. List of Commands 5-7. List of Commands Function This makes the settings for rotating or stopping the spindle, and for spindle rotating speed. Value . Rotation or no rotation (ON: rotation, OFF: stopped) Value . Spindle rotating speed (80 to 300 x 100 rpm) 1: .. 10 SP ON 80 This rotates the spindle at the specified spindle rotating speed, or stops rotation of the spindle. Commands to move the spindle, such as [MOVE-ZM] and [CUT-ZM], do not rotate or stop the spindle by themselves. You specify this with the [SP] command. A setting of [80], for example, sets a spindle rotating speed of 8,000 rpm. 11 P Function This controls the state of the output ports for expansion connector 2. Value . Output-port state (1: High, 0: Low, *: Maintain state) 00000000 1: . 11 P 00000000 Output port 1 Output port 8 This command changes the state of the output ports for expansion connector 2. There are eight output port (numbered 1 through 8), and this controls the state (high or low) of each one. [*] means no change in state -- that is, to leave high if high, or to leave low if lo...

Ce manuel est également adapté pour les modèles :
Autres outils - EGX-400 (2.37 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories