Log:
Évaluations - 0, GPA: 0 ( )

Instructions Adaptec, Modèle Adaptec RAID 3805

Fabricant : Adaptec
Taille : 20.42 kb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Par ce dispositif a également d'autres instructions :

Facilité d'utilisation


Then the ACU will run. On IBM systems, press any key when prompted to load the utility forcibly. The ACU /C0 buildall command does not start a build/verify on RAID 1 or RAID 10 arrays that are being created using the quick init method. 4.8 FreeBSD Adaptec Storage Manager is not supported in FreeBSD; storage management must be done through the Adaptec Configuration Utility (ACU) and ARCCONF command line utility. 4.9 Adaptec Storage Manager After a rebuild and waking up from hibernation, a controller may be detected incorrectly in Adaptec Storage Manager. Press F5 to correct the problem. 4.10 ASR-4805SAS controller When the controller is installed in PCI-E slot 2 of a Dell PE 1800 system, there is no BIOS POST. When the controller is installed in PCI-E slot 3 in a Dell PE 1800 system, the system halts and the keyboard locks up. When the controller is set to boot from a RAID array and a second RAID array is created, the controller may no longer be able to find the boot drive. When the controller is installed in the primary PCIe slot of an Intel 955X or nVidia nForce4 (Intel edition) motherboard, if you use the Adaptec Flash Utility to perform a Mode0 flash, the controller will show incorrectly and cannot be flashed. If a Mode0 flash is required, install the controller in an alternate PCIe slot or alternate computer. 4.11 SAS and SATA controllers and Adaptec 335SAS enclosure When the Adaptec 335SAS enclosure is attached to an Adaptec SAS controller, such as ASR-4800SAS or ASR-4805SAS, the enclosure numbering nomenclature starts with "0". For example, if two Adaptec 335SAS enclosures are connected to a ASR-4800SAS SAS controller, management tools such as Storage Manager will denote the enclosures as "Enclosure 0" and "Enclosure 1". When the Adaptec 335SAS enclosure is attached to an Adaptec SATA controller, such as AAR-2420SA or AAR-2820SA, the enclosure numbering nomenclature starts with "14". For example, if two Adaptec 335SAS enclosures are connected to an AAR-2820SA SATA controller, management tools such as Storage Manager will denote the enclosures as "Enclosure 14" and "Enclosure 15". 4.12 OpenServer 6.0 Arrays may not be displayed correctly, even after you restart your computer. To resolve the problem: As root, run 'resmgr -r -m vtoc' until it fails. Then, as root, run '/etc/conf/bin/idconfupdate -f'. Then, reboot. 4.13 Using the ASR-4800SAS in a Gateway 920 When more than one ASR-4800SAS controllers are installed in a Gateway 920 server, the system will not POST. 4.14 Creating an Array from the Adaptec Storage Manager CD When you create an array with the Adaptec Storage Manager bootable CD, the maximum size of the array is 2 TB. 4.15 Using the controller with an Adaptec S50 JBOD Enclosure Temperature warnings from Adaptec S50 JBOD Enclosure (firmware version T016) are not shown in Adaptec Storage Manager (or on the enclosure). 4.16 SMART errors on SATA controllers During POS...

Ce manuel est également adapté pour les modèles :
Autres composants - Adaptec RAID 3405 (20.42 kb)
Autres composants - Adaptec RAID 3085 (20.42 kb)
Autres composants - Adaptec RAID 31605 (20.42 kb)
Autres composants - Adaptec RAID 31205 (20.42 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories