Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
Turn the dial until it clicks (c). Ensure the dial sits flush against the frame. Insert the swivel into the end of the elbow. 6 Insert the assembled elbow into the mask frame. 7 Reattach the top headgear straps by threading them through the loops. 6 English Troubleshooting Problem Possible reason Possible solution Mask won’t seal properly or is uncomfortable Mask may have been fitted incorrectly or is incorrectly adjusted. Mask is wrong size. Mask cushion is skewed in mask frame. Mask cushion is misaligned or creased on face. Mask cushion may be dirty. Carefully follow instructions in “Fitting the Mask”. Check headgear and dial are not overtightened. Extend dial to apply more force to upper lip. Shorten dial to increase force at nose bridge. Talk to your clinician. Check insertion of cushion and reinsert correctly according to the instructions in “Reassembling the Mask”. Ensure cushion is properly aligned according to the instructions in “Reassembling the Mask”. Make sure the cushion has no creases in it: undo headgear clip, check cushion and reposition the mask over your nose. Clean cushion according to instructions in “Cleaning the Mask at Home”. Mask is too noisy Mask is assembled incorrectly. Reassemble mask. Vents are blocked or partially blocked. Clean vents according to instructions in “Cleaning the Mask at Home”. Dial inserted into mask frame before forehead support Misassembly. Push dial base onto a hard surface until the dial comes out of the frame. Symbols LOTREF Caution, consult accompanying documents; Lot number; Part number; Temperature limitation; Humidity limitation; Does not contain latex; Indicates a Warning or Caution and alerts you to a possible injury or explains special measures for the safe and effective use of the device. 7 Limited Warranty ResMed warrants that your ResMed mask system, including its components: mask frame, cushion, headgear, tubing and other accessories (“Product”) shall be free from defects in material and workmanship for a period of ninety (90) days from the date of purchase by the initial consumer. For further details refer to the Warranty. Technical Specifications Note: The mask system does not contain latex, PVC or DEHP materials. Pressure–Flow Curve The mask contains passive venting to protect against rebreathing. As a result of manufacturing variations, the vent flow rate may vary. 50 Pressure Flow 45 (cm H2O) (L/min) 40 35 4 19 30 25 8 28 20 12 34 15 10 16 40 5 0 20 45 Mask Pressure (cm H2O) 468101214161820 Vent Flow Rate (L/min) Dead Space The dead space of the mask varies according to cushion size. It is Information 128 mL for the Extra Large size. Therapy Pressure 4 to 20 cm H2O Resistance Drop in pressure measured (nominal) at 50 L/min: 0.1 cm H2O at 100 L/min: 0.7 cm H2O Environmental Operating temperature: +41°F to 104°F (+5°C to +40°C) Conditions Operating humidity: up to 95% non-condensing Storage and transport temperature: -4°F to 140°F (-20°C to +60°C) Storage and transport humidity: up to 95% non-condensing Gross S: 140 mm (H) x 91 mm (W) x 93 mm (D) dimensions M, L, LW, XL: 155 mm (H) x 91 mm (W) x 98 mm (D) Mask fully assembled – no headgear. Note: The manufacturer reserves the right to change these specifications without notice. Storage Ensure that the mask is thoroughly clean and dry before storing it for any length of time. Store the mask in a cool dry place out of direct sunlight. Disposal The Mirage Micro does not contain any hazardous substances and may be disposed of with your normal household refuse. 8 ResMed Ltd (Manufacturer) 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia ResMed Corp (US Designated Agent) 14040 Danielson Street Poway CA 92064-6857 USA ResMed (UK) Ltd (EU Authorised Representative) 96 Milton Park Abingdon Oxfordshire OX14 4RY UK ResMed Offices Australia, Austria, Belgium, Brazil, China, Finland, France, Germany, Greece, Hong Kong, India, Ireland, Italy, Japan, Malaysia, Mexico, Netherlands, New Zealand, Norway, Portugal, Singapore, South Africa, Spain, Sweden, Switzerland, UK, USA (see for contact details). Mirage Micro Nasal Mask Protected by patents: AU 710733, AU 741003, AU 766623, AU 775051, AU 777033, AU 785376, CA 2261790, EP 0956069, EP 1187647, EP 1187648, EP 1187649, EP 1187650, EP 1314445, EP 1479406, HK 1057714, JP 3686609, NZ 513052, NZ 526165, NZ 526166, NZ 526167, NZ 526168, US 6112746, US 6119693, US 6357441, US 6374826, US 6439230, US 6463931, US 6532961, US 6557556, US 6581594, US 6581602, US 6634358, US 6691708, US 6823865, US 6860269, US 6871649, US 6997188, US 7011090, US 7159587, US 7178527, US 7188620, US 7216647, US 7234466, US 7243651. Other patents pending. Protected by design registrations: AU 304309, CN 200530117106.1, EP 366844, JP 1264474, NZ 406357, US D532512, US D547439, US D545960. Others pending. AutoSet CS, Mirage and Mirage Micro are trademarks of ResMed Ltd. AutoSet CS and Mirage are registered in U.S. Patent and Trademark Office. Velcro is a registered trad...