Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
It uses only 2" (5 cm) between the projector and the ceiling to conveniently and securely enclose the products out of sight above the display device. • PMP Series Projector Mounting Poles — Available in fixed lengths of 4" (10 cm), 6" (15 cm), 10" (25 cm), and 12" (30 cm), PMP Projector Mounting Poles are used with the PCM 240 and UPB 25 to create individualized installations. Each pole includes a cutout, which provides convenient cable access. • UPB 25 Universal Projector Mounting Bracket — The Extron UPB 25 universal projector mount is compatible with nearly every projector having a weight of up to 25 pounds (11 kg). It features independent adjustment of roll (±4 degrees of horizontal tilt), pitch (±25 degrees of vertical angle) and yaw (360 degrees of rotation on a pole mount, or 10 degrees when mounted flush to the ceiling) for precise control of each axis and exact alignment of the projector. Locking mechanisms maintain the original positioning settings when servicing requires the projector and attached arm assembly to be removed from the mounting assembly. About this Manual This manual discusses how to safely install and use the Extron PCM 240 Projector Ceiling Mount. About the PCM 240 projector ceiling mount The Extron PCM 240 Projector Ceiling Mount is a versatile ceiling plate for installation in classrooms or boardrooms with 2' x 2' or 2' x 4' T-bar style suspended ceiling. The PCM 240 should be secured to the structural ceiling, above the suspended ceiling tiles, using turnbuckles and tie wire. Once secured in place, it is easily fixed to the suspended ceiling T-bar with the supplied screws. When properly installed, it can hold up to 50 pounds (23 kgs) of A/V equipment. The projector mounting pole is easily installed in the threaded pipe adapter mounted on a sliding plate, allowing horizontal adjustment for correct alignment. The PCM 240 includes mounting holes for Extron 3" deep, . rack wide devices (e.g. MPA 122), and has two openings for Raco (catalog #8471) or UL junction box insertion, providing integral power access points, video connection, or simple cable pass-throughs. Extron UPB 25 Universal Projector Mounting Bracket Extron PCM 240 Projector Drop Ceiling Mount ExtronPMK 350Low Profile ProjectorMounting KitExtron Power Supply for MPA 122 Projector Extron PMP 6”, 10“ or 12” Projector Mount Pole BASS LEVEL TREBLE MINI POWER AMPLIFIER MPA 122 ON OFF LIMITER STEREO DUAL MONO Extron MPA 122 Mini Power Amplifier Figure 1 — Typical application of PCM 240 PCM 240 Projector Ceiling Mount • Introduction PCM 240 Projector Ceiling Mount • Introduction 3 2 Installation Installing the PCM 240 Before starting, check that all the parts received match the supplied parts list (see “PCM 240 kit contents” table, page 10). Preparing the ceiling W The PCM 240 must not be supported by the suspended ceiling itself. It must be secured to and suspended from the structural ceiling above. W Check the structural ceiling to ensure that it can handle a load four times the weight of the final setup. N Refer to local building standards and codes to verify that the installation will meet all the regulatory requirements. Identify the location for projector placement. Remove the ceiling tiles adjacent to the tile where the projector will be mounted. This will allow easy and safe access while installing the projector mount. Inspect the structural ceiling where the projector mount will be installed to ensure there are no cracks or weaknesses that could jeopardize the completed installation. Select the correct installation hardware from those supplied. Hardware for each of three methods of hanging and securing the PCM 240 is supplied: • Turnbuckles and tie wire tied to concrete anchors for concrete structures • Turnbuckles and tie wire tied to eye screws for joists • Turnbuckles and tie wire wrapped around wooden trusses. Alternatively, threaded rods (not supplied) may be used to secure the mount to the ceiling structure. Safety cable is provided to hold the mount up in the event that any tie wire or rods become loose or detached as a result of an earthquake or accident. Installing the projector ceiling mount 1. Screw the four T-bar securing screws loosely into the ends of the mounting plate (see figure 2). Attach Turnbuckles to Long SidesT-bar Securing ScrewsPipe Adapter Plate Lock Nuts10Attach Ceiling Anchors and Wire10 Degrees from Vertical. T-barMounting Plate Figure 2 — Installing the PCM 240 2. Place the mounting plate over the selected ceiling tile and lower onto the T-bar. Adjust to the position desired and lightly tighten the T-bar securing screws to the frame. 3. Adjust the sliding pipe adapter plate to the precise position for the mounting pole, and tighten down the locking nuts. 4. Using the hole in the pipe adapter plate as a guide, mark the ceiling tile where the mounting pole will pass through it. If electrical boxes are also to be installed, mark the ceiling tile where the cut-outs will be. 5. Loosen the T-ba...