Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
See “Using the On-Screen Menus” on page 20 for details. FIGURE 12 Keypad and remote buttons Menu Press the menu button to open the on-screen menus. Press menu again to close the menus. When you close the menus, the projector saves any changes you made. For more information about the on-screen menus, see page 20. source volume volume + standby menu right mouse button left mouse button LED Mouse buttons Use the mouse buttons to adjust settings in the menus. See “Using the On-Screen Menus” on page 20. Source (keypad only) or Computer and Video (remote only) When you have more than one source (computer and video) connected to the projector, select between them by pressing the source button on the keypad or the computer or video button on the remote. Standby When you press standby, the display and audio turn off and a blank screen is displayed for 15 minutes. You can change the amount of time the projector stays in standby mode; see “Standby Time” on page 27 for details. The LED lights orange while the projector is in standby. • If you press standby again within 15 minutes, the projector returns to normal operations immediately. The LED changes from orange to green. • If you press standby again after 15 minutes, there is about a 60 second delay before the lamp turns back on. The LED flashes green while the lamp is re-lighting. • If you don’t press standby again, the lamp turns off after 15 minutes. The LED lights orange while the projector is in standby. Volume (keypad only) To increase the volume, press volume + . To decrease the volume, press volume . Volume adjustments are saved for each source you have connected. Using the Projector NOTE:Some menu items may be grayed out (dimmed) at certain times. This indicates the item is not applicable to your setup (for example, video standards do not apply to computer sources) or the item is not enabled until another selection is made (for example, Manual Tracking is not available until Auto Image is turned off). Using the On-Screen Menus The projector has six drop-down menus that allow you to make image adjustments and change a variety of settings. Most of these adjustments aren’t available directly from the keypad. To open the on-screen menus, press the menu button on the keypad or remote. This changes the volume, source, and standby buttons on the keypad to menu navigation buttons. Press the corresponding buttons to move the cursor up, down, left, or right, or use the disk mouse on the remote. To select a menu, move the cursor left or right to highlight the menu you want. The drop-down menu appears. Display Audio Image Controls Language Status> > Brightness Contrast Tint Color Sharpness Blank screen blue Reset all menu source volume volume + use these four buttons to navigate through the menus standby FIGURE 13 Keypad navigation buttons and drop-down menu To change a menu setting, use the up and down navigation buttons on the keypad or the disk mouse on the remote to move the cursor up and down to the item you want to change (the selected item is highlighted), then use the left and right mouse buttons to adjust a setting. Some submenus, such as Brightness, consist of a slider bar you use to increase or decrease a value; some submenus, such as Standby Time, consist of options you scroll through to select the desired one. All changes are saved when you close the menus. To access another menu, use the left and right navigation buttons to move to the desired menu. Display Menu Display> >Audio Image Controls Language Status Brightness Contrast Tint Color Sharpness Blank screen blue Reset all FIGURE 14 Display menu Brightness Adjusting the brightness changes the intensity of the image. • Press the left mouse button to darken the image. • Press the right mouse button to lighten the image. Contrast The contrast controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image. • Press the left mouse button to decrease the contrast. • Press the right mouse button to increase the contrast, making the blacks appear blacker and the whites appear whiter. Tint The tint adjusts the red-green color balance in the projected image. • Press the left mouse button to increase the amount of green in the image. • Press the right mouse button to increase the amount of red in the image. Using the Projector Color The color setting adjusts a video image from black and white to fully saturated color. • Press the left mouse button to decrease the amount of color in the image. • Press the right mouse button to increase the amount of color in the image. Sharpness This setting adjusts the sharpness of a video image and is available on the CD-455m and CD-555m only. • Press the left mouse button to decrease the sharpness. • Press the right mouse button to increase the sharpness. Blank Screen Blank Screen determines what color is displayed when there is no active source and when the projector is in standby...
Ce manuel est également adapté pour les modèles :Projecteurs - CD-455m (450.32 kb)
Projecteurs - CD-454m (450.32 kb)