Use one screw to fix the three grounding wires to the preformatter 6. Fix the preformatter unit to the input module using four screws Image 3-18 Preformatter unit: front screws 7. Install the covers (see concerning chapters): - engine fan cover 1 - topcover - rear cover 3.3 Restoring the backup Procedure Restore the backup using Projector Support tool. For more details, see "Backup and restore data", page 15. 3.4 Upgrade the projector to the desired software version Introduction Projector upgrade is done through Ethernet. Prior to starting the procedure below, make sure the Ethernet settings in the OSD are set to the correct values to make Ethernet communication possible between computer and projector. R59770498 PMP KIT 28/02/2011 13 3. Kit installation (detailed ) Necessary tools Computer or laptop, connected to the projector through Ethernet How to upgrade the projector software? 1. Enter the correct Ethernet settings in the OSD of the projector 2. Download the desired upgrade tool to your computer or laptop 3. Run the upgrade tool NW- x v03.01.0001.exe device version Image 3-19 Upgrade tool: example for NW-12 and Galaxy NW-12 CAUTION: Refer to the User guide to enter the Ethernet settings in the OSD of the projector R59770498 PMP KIT 28/02/2011 A.Backupandrestoredata A. BACKUP AND RESTORE DATA Overview • Connecting to the projector through Projector Support • Making a backup of the projector’s key data • Restoring a set of key data About this chapter It is extremely important to make backups of your projector data after each setting change. This chapter describes how to use Barco’s Projector Support software tool to make a backup of the key data of a projector and how to restore this backup. A full backup holds the full set of data which is available on the PMP of the projector: • panel settings • projector settings • standard/customer files • serial number • history • runtimes • option key • etc. Recovery of the serial number and the runtimes is possible, on condition that the processor of the target PMP does not contain this information yet (i.e. it must be a new PMP). Ina(local)networkwheremultiplePMPboardsarepresent,onlyreplaceonePMPatatimetopreventrestoring a backup to a wrong PMP. CAUTION:Abackup fileincludesalignmentdatathatisrelatedtotheoriginalprojectoronly: uploadingthese files to another projector may result in bad image quality! CAUTION: Pressing in the Tools section deletes all data from the PMP, even default settings and factory data! A.1 Connecting to the projector through Projector Support How to connect to the projector? 1. Add both the projector and the computer to the same (local) network 2. Switch on the projector and leave it in standby mode 3. On the computer, run the Projector Support tool R59770498 PMP KIT 28/02/2011 A.Backupandrestoredata Image A-1 Projector Support tool: user interface 4. In the Communication Parameters section, enter the IP address or the hostname of the projector Image A-2 Projector Support tool: enter IP address or hostname R59770498 PMP KIT 28/02/2011 A.Backupandrestoredata Tip: You can also press the Query button. A list appears, showing all the projectors that are connected to the same network. In this list, select the desired projector and hit OK. Image A-3 Projector Support tool: select Query Image A-4 Projector Support tool: example of a query list Special case in the Query list If DHCP is disabled in the projector’s network settings and the fixed IP address of the projector (PMP) is not known and happens to be outside the range of the local network, the PMP is listed in red font. Image A-5 Projector Support tool: example of a query list R59770498 PMP KIT 28/02/2011 A.Backupandrestoredata Select it and hit OK to open a new window where the network settings can be manually changed. It is advised to switch DHCP to On to continue. Image A-6 Projector Support tool: change DHCP setting to ON Image A-7 Projector Support tool: confirm network settings A.2 Making a backup of the projector’s key data How to make a backup of the projector’s key data? It is assumed that communication with the projector has been established through Projector Support. 1. In the Backup section of the Projector Support tool user interface, hit Browse R59770498 PMP KIT 28/02/2011 a Image A-8 Projector Support tool: select browse in the Backup section 2. Select a target folder on the computer to save the backup of the projector data Image A-9 Projector Support tool: browse to the backup folder 3. Change the file name (optional) and hit Save Image A-10 Projector Support tool: change the name of the backup file (optional) 4. In the Backup section, hit All settings R59770498 PMP KIT 28/02/2011 A.Backupandrestoredata Image A-11 Projector Support tool: start the backup of all settings 5. Wait for the backup process to be finished. Image A-12 Projector Support tool: progress bar A successful backup is indicated by a green oval. Image A-13 Projector Support tool: backup succes...
)
