Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
NOTE Refer to "Rear Side and Cables" on page 10 for cables used for connection. Setting up the PC Environment 1 Click the right mouse button on the Windows wallpaper 1 and click on Properties. Display Properties tab will appear. 2 Click on Settings tab and set the Screen resolution by referring to Resolution described in the display mode table supported by this projector. You do not have to change Color quality setup. 3 Press the Advanced button. Another property window will appear. 4 Click on Monitor tab and set the Screen refresh rate by referring to Vertical Frequency described in the display mode table supported by this projector. ¦ Set up both the vertical and horizontal frequency instead of Screen refresh rate. 5 Press the OK button to close the window and press the OK button in Display Properties window to close. The computer might begin restart automatically. 6 Shut down the PC and connect to the projector. (Page 60) Setting 2 3 4 Process might vary depending on the type of computers or Windows versions. This appliance supports up to 32 bits per pixel in Color quality when it is used as a PC monitor. NOTE Projected images may differ from the monitor depending on monitor manufacture or Windows versions. ¦ If a band or an unusual signal appears on the projector when PC is turned off or disconnected, switch to Composite mode using the SOURCE button or check that PC is properly connected. ¦ When connecting the projector to PC (including DVI connection), check that PC setup complies to display settings supported by this projector. If not, there may be signal problems. Connecting Connecting to PC You can connect a PC to the projector and use it as a monitor. Using PC Video Cable or DVI Cable Rear side of Projector DVI-D Video Cable PC Video Cable or Rear Connection DVI-D Port Connect PC (RGB In) port on the rear side of the projector to the monitor output port of PC using PC video cable. ¦ If PC has a DVI output port, connect it to DVI port of the projector. This product supports Plug & Play. No driver installation is needed for Windows XP. NOTE Viewing the PC Screen Turn on the projector and press the PC button 1 to select PC. If the projector is connected to PC PC DVI, press the DVI button to select DVI. 1 ¦ If PC Mode is not available, check PC video cable is in place. Turn on the PC and set the PC Environment 2 when necessary. (Page 59) Adjust the screen. (Pages 62~65) 3 Connecting to PC Connecting to PC Enjoy better picture quality by using DVI-D cable (supports digital signals only) instead of PC Video cable. NOTE DVI-I cable (supports analog signals) is not supported. Use DVD-D cable. Sound comes out from PC speakers. Pin Configuration of PC Video Port Plug PC Video Cable DVI-D (15-pin signal) (supports only digital signals) Pin No. PC Input 1 Red (R) 2 Green (G) 3 Blue (B) 4 Ground 5 Ground (DDC) 6 Red (R) Ground 7 Green (G) Ground 8 Blue (B) Ground 9 Reserved 10 Ground Sync 11 Ground 12 Data (DDC) 13 Horizontal Sync 14 Vertical Sync 15 Clock (DDC) Pin No. Signal Pin No. Signal 1 T.M.D.S. DATA213 T.M.D.S. DATA3+ 2 T.M.D.S. DATA2+ 14 +5V Power 3 T.M.D.S. DATA2/4 Shield 15 Ground for 5V 4 T.M.D.S. DATA416 Hot Plug Detect 5 T.M.D.S. DATA4+ 17 T.M.D.S. DATA06 Clock (DDC) 18 T.M.D.S. DATA0+ 7 Data (DDC) 19 T.M.D.S. DATA0/5 Shield 8 No Connection 20 T.M.D.S. DATA59 T.M.D.S. DATA121 T.M.D.S. DATA5+ 10 T.M.D.S. DATA1+ 22 T.M.D.S. Clock Shield 11 T.M.D.S. DATA1/3 Shield 23 T.M.D.S. Clock+ 12 T.M.D.S. DATA324 T.M.D.S. Clock- Connecting PCCAUTION DVI-D cable does not support analog RGB signals. This appliance supports VESA Plug & Play and recognizes connection to PC automatically. VESA Plug & Play Connecting Automatic Picture Adjustment Used to adjust frequency and phase of PC screen automatically. Connecting to PC Automatic Picture Adjustment Before adjusting! Set the input mode to PC. 1 MENU 2, 3, 4 Select 2, 3 …/† 5 EXIT PC Press the MENU button. The main menu is displayed.1 Press the or button to move to Setup. 2 The Setup menu is displayed. Press the button. Press the or button to move to PC, then3 press the button. The Auto Adjustment is selected. Press the button. 4 Auto Adjustment in progress message is displayed and PC screen is adjusted automatically. 5 Press the EXIT button to exit the menu. Auto Adjustment in Progress.. Please Wait Setup Install : Front-Floor v Light Setting : Theater v V-Keystone v Test Pattern v PC v Factory Default v Information v Move Enter Return PC Auto Adjustment v Coarse 1344 Fine 0 Zoom v Reset v Move Enter Return Frequency Adjustment Used to adjust frequency when vertical lines appear on PC screen. Frequency 1 MENU 2, 3, 4 Select 2, 3, 4 …/†/oe/v 5 EXIT Before adjusting! Set the input mode to PC. PC Press the MENU button. The main menu is displayed.1 Press the or button to move to Setup. The Setup menu is displayed. Press the button. 2 Press the or button to move to PC, then press the button. The PC menu is displayed. 3 Press the EXIT button to exit the ...
Ce manuel est également adapté pour les modèles :Projecteurs - SP-H500AE (4.28 mb)
Projecteurs - SP-H700AE (4.28 mb)