Évaluations - 2, GPA: 4.5
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
.This is not supported in [AV] and [S-Video] modes. .This is supported only when the input signal is AV Timing(D-Sub) . .If Overscan is turned off, unnecessary extra parts at the edges of an image may also be shown, though you can view more of the area. In this case, turn Overscan on. Film Mode Using this function, you can set the display mode so it is optimized for playing movies. 1) Off 2) On . Film Mode can only be supported for the [AV], [S-Video], 480i, and 576i of AV Timing(D-Sub) signals . PC Eliminates or reduces noise that causes unstable screen quality, such as screen shaking. If the noise is not removed using Fine Adjustment, adjust the frequency to the maximum and Auto then perform Fine Adjustment again. Adjustment . It is only enabled for the PC Timing input of the D-Sub terminal. . Refer to PC Timing. 1) Auto Adjustment : Used to adjust frequency and phase of PC screen automatically. Coarse 2) Coarse : Used to adjust frequency when vertical lines appear on PC screen. Fine 3) Fine : Used to fine tune the PC screen. 4) Reset : Using this function, you can reset the PC menu settings to the factory default settings. Reset Zoom Enlarges the PC screen to 2X, 4X, or 8X. . This can only be adjusted when the input signal is PC Timing. | Basic Functions | Input | Picture | Setup | Option | * Click the Play( )/Stop( ) button in the table below to view the video file. Screen Description Play/Stop Adjustment Install To tailor the picture to the installation location, you can invert the projected images vertically/horizontally. 1) Front-Floor : Normal Image 2) Front-Ceiling : Horizontal/Vertical Reversed Image 3) Rear-Floor : Horizontally Reversed Image 4) Rear-Ceiling : Vertically Reversed Image Lamp Mode Used to set the image brightness by adjusting the amount of light generated by the lamp. 1) Eco : This mode is optimized for small screens smaller than 100 inches. Eco This mode decreases the lamp brightness and power consumption in order to extend the lamp lifetime and reduce noise and power consumption. 2) Bright : This mode maximizes the lamp brightness when the ambient illumination is Bright bright. As the brightness of the lamp increases, the lamp lifetime can be reduced and the noise and power consumption may increase. V-Keystone If video scenes are distorted or tilted, you can compensate for this using the vertical Keystone function. . The sound output of your projector is temporarily stopped while the keystone is being changed. . The keystone is not compensated for in the On Screen Display (OSD). Background You can set the Background that is displayed when there is no signal from the external device connected to the projector.If a signal is received, the Background you set disappears and a normal screen is displayed. 1) Logo 2) Blue 3) Black Test Pattern Generated by the projector itself. Utilized as standard to optimize the installation of the projector. Crosshatch 1) Crosshatch : You can check whether the picture is distorted or not. 2) Screen Size : You can refer to picture format sizes such as 1.33:1 or 1.78:1. Screen Size Video Type Allows you to set the type of input signal when your projector fails to determine this automatically in PC mode. . In [PC] mode, this is only enabled if the input signal is AV Timing(D-Sub). However, for a separate H/V sync., this is only enabled for 1280 x 720p 59.94 Hz/60 Hz signals. 1) Auto 2) RGB(PC) 3) RGB(AV) 4) YPbPr(AV) Usage Color, Sharpness,Tint PC menu and zoom RGB(PC) When connecting the RGB output of a PC to the D-Sub terminal Disable Enable RGB(AV) When connecting the RGB output of an AV device (STB, DVD, etc…) to the D-Enable Enable Sub terminal YPbPr(AV) AV device (STB, DVD, etc…) to the D-Enable Disable When connecting the YPbPr output of an Sub terminal Auto Auto settings -- Reset Using this function, you can reset various settings to the factory default settings. Factory 1) Factory Default : Changes the settings to the factory defaults. Default 2) Reset Filter Time : Resets the filter time. Reset Filter Time | Basic Functions | Input | Picture | Setup | Option | * Click the Play( )/Stop( ) button in the table below to view the video file. Screen Description Play/Stop Adjustment Language You can select the Language used for the menu screen. Menu Option 1) Position You can move Menu Position up/down/left/right. 2) Transparency Position You can set the translucency of menu. - Low - Medium Transparency - High - Opaque Display 3) Display Time Time You can set the display time of the menu. -5 sec / 10 sec / 30 sec / 60 sec / 90 sec / 120 sec / Stay On Sound Adjusts the right and left audio balance and equalizer of the 3W stereo speaker embedded in the projector. 1) Balance 4) 1kHz 2) 100Hz 5) 3kHz 3) 300Hz 6) 10kHz Filter Check Sets the check period for the filter. (Unit: hour) Time 1) Off 2) 100 3) 200 4) 400 5) 800 . If the filter usage time is larger than the filter check period, the filter check message is displayed for a minute whenever the proje...
Ce manuel est également adapté pour les modèles :Projecteurs - L250 (1.25 mb)
Projecteurs - SP-L200 (1.25 mb)
Projecteurs - SP-L220 (1.25 mb)
Projecteurs - SP-L220W (1.25 mb)