Évaluations - 3, GPA: 3.7
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
Refer to Action 4 below. 0 0 . This indicates that the power is turned off automatically because the internal temperature of the projector has increased beyond the maintenance limit. Refer to Action 5 below . . . A problem has occurred with the operation of the lamp. Refer to Action 6. . . . The lifetime of the lamp has expired. Refer to Action 7. . . . The power for the product is not operating normally. Contact a service center. Clearing Indicator Problems Measures If the symptom remains even after disconnecting and then reconnecting the power cord and turning the projector on again, contact your product provider or our service center. Check if the screws on the side of the projector are correctly locked, and if they are locked normally, contact your product distributor or a service center. Open the lens cover completely. If the lens cover is not open completely while operating the projector, Classification Action 1 Action 2 State When the cooling fan system is not in normal operating condition. When the lamp cover protecting the lamp unit is not properly closed or the sensor system is not in normal operating condition. The status that the lens both the video and audio are turned off automatically. If this status persists for ten minutes, the projector is turned off automatically. If the internal temperature of the projector has increased beyond the maintenance limit, it is changed to Cooling mode before it is turned off automatically. * Cooling mode: The status that the fan speed has increased and the lamp of the projector has been changed to ECO mode by force. Check whether the ventilating hole of the projector is blocked. Check whether the air filter is blocked. Clean it if it is blocked. Check whether the surrounding temperature of the projector is higher than the standard temperature range of the projector. Cool the projector sufficiently and operate it again. Check whether the ventilating hole of the projector is blocked. Check whether the air filter is blocked. Clean it if it is blocked. Check whether the surrounding temperature of the projector is higher than the standard temperature range of the projector. Cool the projector sufficiently and operate it again. If the same problem occurs continually, contact your product distributor or service center. Turn the power off, wait for a sufficient amount of cooling time and then turn the power on to operate. If the same problem occurs continually, contact your product distributor or service center. Check the lamp usage time on the Information Display screen. If you need to replace the lamp, contact your product distributor or service center. cover is not open Action 3 completely. This indicates that it has changed to Cooling mode, because the internal Action 4 temperature of the projector has increased beyond the maintenance limit. If the internal temperature of the projector increases higher than Action 5 the limit, it is turned off automatically. The lamp malfunctions after power turns off Action 6 abnormally or after powering on right after turning off the projector. When the screen becomes Action 7 darker This Projector uses a cooling fan system to keep the unit from overheating. Operation of the cooling fan may cause noise, which does not affect the product performance and is part of normal operation. Rear Side 1. PC OUT port 7. [AV IN] VIDEO Input port 2. AUDIO OUT port 8. [AV IN] S-VIDEO Input port 3. HDMI/DVI IN Input port 9. PC IN 1,2 Input port 4. PC 1/DVI AUDIO IN Input port 10.[PC IN2] AUDIO Input port 5. RS-232C port (For service input terminals) 11.Remote Control Signal Receiver 6. [AV IN] R-AUDIO-L Input port 12.POWER Input port | Product Features | Product Views | Remote Control | Product Specifications | 1. POWER ( ) Button 2. AUTO Button 3. MENU ( ) Button 4. Move (^ Ў . .)/( ) Button 5. V.KEYSTONE(+/-) (VERTICAL KEYSTONE)Button 6. INSTALL Button 7. BLANK Button 8. P.SIZE Button 9. QUICK utton 10. MUTE ( ) Button 11. RETURN ( ) Button 12. EXIT ( ) Button 13. VOL Button 14. INFO Button 15. SOURCE Button 16. P.MODE Button 17. STILL Button 1.POWER( ) Used to turn on the projector. 2. AUTO Adjusts the Picture automatically. (Available in PC Mode Only) 3.MENU( ) Used to display Menu Screen. 4.Move (^ Ў . .)/( ) Used to move to or select each menu item. 5. V.KEYSTONE(VERTICAL KEYSTONE) (+/-) Use this when video scenes are distorted or tilted. 6. INSTALL Used to flip or reverse the projected image. 7. BLANK This is used to turn off the video and audio temporarily. It is released when any button other than the POWER button is pressed. 8. P.SIZE Used to adjust the size of picture screen. 9. QUICK This is used when quickly selecting the last used menu. 10. MUTE ( ) This is used to temporarily mute the sound. To hear sound again, press the MUTE button again or press the - VOL + button. 11. RETURN ( ) Returns to the previous menu. 12. EXIT ( ) Used to make Menu Screen disappear. 13. VOL Adjusts the volume. 14. INFO Used to check source signals, pi...
Ce manuel est également adapté pour les modèles :Projecteurs - L300 (2.13 mb)
Projecteurs - SP-L300 (2.13 mb)
Projecteurs - SP-L300WG (2.13 mb)