Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
Sets projection mode in accordance with Placement Style. Set the time to wait for the power to be turned off after the last operation is made with no input signal. Off (not turned off) 30 min. Set whether the input with signals is only selected or not. Sets whether to turn on the power when the ON/STANDBY button is pressed (Manual), or when the power cord is plugged in (Auto). Manual Auto Sets the lamp power. Sets the cooling fan speed. When two or more projectors are used and controlled by the remote control respectively, this menu sets the code for the projector and the remote control. [ or : Enter setting mode] [ : Select item] [ : Select from 1, 2, 3, 4] [ :Confirm] [ :Select OK to end] Press [Cancel] to return. Lock the control panel buttons. [ or : Enter setting mode] [ : Select item] [ : Select On/Off] [ :Confirm] [ :Select OK to end] Press [Cancel] to return. Press . (The password and user logo are not reset.) Resets all adjustments and settings to their factory settings. Password function When [Password] is [On], the Password Setting screen is displayed. Item Description Projection mode No signal power off Auto input search Power on Lamp power Fan mode Remote control Key lock Reset all Password (Standard) (Rear) (Ceiling) (Rear ceiling) On Off Standard High Yes No Off On Low Standard p.21 p.32 Detailed description [Auto input search] [On]: Automatically searches the signals that can be projected, and switches input from the connected device that outputs the video signals each time the INPUT button is pressed. The input from the connected device that outputs no video signals is skipped. [Off]: Displays the Input select menu. Toggle with buttons and press button. (The input without signals can be selected.) [Power on] Note that if [Power on] is set to [Auto], then if the power is supplied when restored after a power outage, the projector will come on. [Lamp power] When [Lamp power] is set to [Low], the screen becomes a little darker, but the cooling fan noise gets quieter. [Fan mode] Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise gets louder.) Set this option to use the projector, for example, at high altitude (over 1,500 meters above sea level). • Do not set Fan mode to [High] when using the projector at a lower altitude. [Remote control] Sets a remote control code from 4 types. You can set each code respectively for up to 4 projectors. The factory setting is [1]. To switch codes, set the same code for the projector and the remote control. A remote control code is applied after the setting is done. • You cannot operate the remote control if the codes of the projector and the remote control do not match. Remote control code setting for remote control Remove the battery cover and set the same remote control code switch as the projector. p.16 (Use a screwdriver with thin tip to set.) [Key lock] Protect from operating errors by locking on the control panel buttons of the projector. (The remote control operations are available.) Control panel operations are locked after the setting is done, and accordingly operation with the control panel buttons is disabled. • To release the key lock, set the [Key Lock] to [Off] using remote control. Pressing the [RETURN] button on the projector for 10 seconds also sets the [Key Lock] to [Off]. (In the latter case, the LAMP, TEMP, and FAN indicators light in orange for 3 seconds.) Computer 1 Y/PB/PR 1 Computer 2 Y/PB/PR 2 Video S-video Input select ......../........shows whether signal is input or not. Input select menu Using the menus (Continued) Using ¦ Displaying This displays information about the input etc. “Yes”: displayed, “No”: not displayed Item Description Computer Y/PB/PR Video S-video Projector Input Input source name Yes Yes Yes Yes Mode name RGB input mode [Note 1] Yes No No No Resolution Resolution (in dots) Yes No No No Frequency Sync frequency Yes No No No Sync Sync signal polarity [Note 2] Yes No No No Signal format Y/PB/PR signal format No Yes No No Video mode Color method of video signal No No Yes Yes Lamp time Time of lamp use [Note 3] Yes Yes Yes Yes Lamp reset count The count for lamp replacement Yes Yes Yes Yes Total time The total time that this projector is used. Yes Yes Yes Yes Version Firmware version [Note 4] Yes Yes Yes Yes Notes 1: The mode of supported RGB signals p.50 is shown. 2: Sync signal polarity shown as P (positive) or N (negative) for [H/V]. 3: Displays [ Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult with a dealer about getting replacement for: TLPLW10 (sold separately). 4: [ Version] shows the version of the projector’s internal control program. This version is referred to for customer service, etc. Note • The displayed information will not be refreshed if the status changes. To refresh the information, dismiss the display, then display it again. About The product’s l...
Ce manuel est également adapté pour les modèles :Projecteurs - TDP-T99U (5.42 mb)