Évaluations - 3, GPA: 4 ( )

Fabricant : Toshiba Taille : 4.19 mb Nom Fichier : Langue d'enseignement:

• If a no signal is being input from the connected device, the icon will appear. • If an unavailable operation button is pressed, the icon will appear. 28 Using To operate via the remote buttons, [ PJ MODE] must be selected. Press the PJ Mode The button lights up. This light will go out seconds after operations are complete. If necessary, press the button again. Using auto setting This function sets up the projector Remote each type of the input signal by using simple operations. Control Control panel INPUT ON/STANDBY 1 Press the AUTO SET button. The Auto setting menu appears. AUTO KEYSTONE MENU 2 Press the AUTO SET button again. AUTO SET VOL. - VOL. + The menu item is automatically adjusted/set. For computer input, the icon will appear during FAN TEMP LAMP ON processing. ON/STANDBY AU TO KEYSTONE MUTE AUTO SET FREEZE INPUT R-CLICK PJ MODE LASER VOL. - OFF VOL. + MENU / ENTER RESIZE Note • Auto adjustment/setting may not be performed correctly for input signals other than those supported by the projector p.69 , p.70 . Manual adjustment and setting The menu items vary according to the input type, as shown in the table below. Use the buttons to adjust the items in the table below, then press the button when you are finished. The menu disappears. Input Item Description Computer (1) Computer (2) ct ItemPhase Adjust with to eliminate flicker. Frequency Adjust with to eliminate periodic patterns and flickering when many vertical lines appear in the screen. SeleH-position Move left Move right V-position Move up Move down Y/PB/PR(1) Y/PB/PR(2) Select ItemPhase Adjust with to eliminate flicker. Signal format [ : Enter to setting mode] [ : Select one of the following] [Apply: ] 480i(525i)@60Hz/480p(525p)@60Hz/ 576i(625i)@50Hz/576p(625p)@50Hz/ 720p(750p)@60Hz/720p(750p)@50Hz/ 1080i(1125i)@60Hz/1080i(1125i)@50Hz/ 1035i(1125i)@60Hz/1152i(1250i)@50Hz Video S-video Video mode [ : Enter to setting mode] [ : Select one of the following] [Apply: ] NTSC/PAL/SECAM/PAL-N/PAL-M/PAL60/NTSC4.43 Camera Shutter speed Set to local line frequency: 50Hz 60Hz Operations 29 Using Using Correcting Freezing the Remote When the foot adjuster p.28 is used to change Remote The image being projected This function is to Control Control projection angle, the picture will undergo (trap- Control panel be used to pause a video a presentation, etc. INPUT ON/STANDBY ezoidal) distortion. Press the remote control’s FREEZE button. AUTO KEYSTONE This projector is capable of correcting this keystone distortion. MENU The picture is paused. The Freeze function is released when pressing the FREEZE button again. ON/STANDBY AU TO KEYSTONE MUTE AUTO SET FREEZE INPUT R-CLICK PJ MODE LASER VOL. + VOL. MENU / ENTER RESIZE OFF Notes • The icon will appear while freeze is in effect. ON/STANDBY AU TO KEYSTONE MUTE AUTO SET FREEZE INPUT R-CLICK PJ MODE LASER VOL. + VOL. MENU / ENTER RESIZE OFF • The freeze function can be used on the resize function. Other operations will release the freeze. • Even if an image is frozen on the projector, it is still changing on the video or other AUTO SET VOL. - VOL. + Before correction After correction US B C O M P U T E R( Y , PB / P R ) S - VI D E O V IDE O V I D E O R - AUDI O - L A U D I O M O N IT O R C O N T R O L 1 2 FAN TEMP LAMP ON q Press the AUTO KEYSTONE button. equipment. The Keystone menu appears. Enlarging the picture size (Resize) w Press the AUTO KEYSTONE button again. The image being projected can be enlarged. The keystone distortion is automatically corrected. The icon will appear during processing. 1 Press the remote control’s RESIZE button. The enlargement ratio is increased each time the RESIZE button is pressed. Manual adjustment While the button is pushed, the image continues increasing to a limit. Use the buttons for keystone adjustment. When the adjustment is finished, press the button. The menu disappears. Item Description Keystone Shrink screen bottom Shrink screen top 2 To decrease the enlargement ratio, press the remote control’s RESIZE button. The enlargement ratio is decreased each time the RESIZE button is pressed. Notes (The image cannot be shrunk to less than its original size. ) • Depending on the amount of keystone adjustment and the contents of images, Remote some information may be lost, or the picture quality may suffer. Control • Keystone adjustment will not change the shape of the menus. ON/STANDBY AU TO KEYSTONE MUTE AUTO SET FREEZE INPUT R-CLICK PJ MODE LASER + VOL. MENU / ENTER RESIZE OFF 3 Press and hold down the buttons to move the enlarged area. e qwr Cutting off the picture and sound temporarily (Mute) Remote When you want to temporarily project the images of another projector, Control overhead projector, etc., this projector’s images and sound can be turned 4 Press the OFF button to undo the resize. ON/STANDBY AU TO KEYSTONE MUTE AUTO SET FREEZE INPUT R-CLICK PJ MODE LASER VOL. + VOL. MENU / ENTER RESIZE OFF off. Press the remote control’s MUTE button. The resize is released, a...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :