Évaluations - 2, GPA: 5
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
Resets all adjustments and settings to their factory settings. Yes No Detailed description [Screen size] • If “Thru” is selected for [Screen size], portions exceeding the native resolution (1024 . 768 pixels) will not appear on the screen. Note that for RGB signals with clock frequency 110MHz or lower, all input pixel signals are properly sampled. However, if the clock speed is higher than this, the RGB pixel signal is thinned before sampling. • If you use the screen size setting function on commercial video software, broadcast or cable-broadcasting programs to display images with the varying aspect ratio except for the purpose of your private viewing and listening, it may infringe the copyright protected by the copyright laws. [Background] • TOSHIBA is set for [Logo] by factory setting. Using the menus (Continued) ¦ The default setting menu This menu shows placement status and other settings. Item Description Projection mode Sets projection mode in accordance with Placement Style. p.21 (Standard) (Rear) (Ceiling) (Rear ceiling) Auto input search Sets whether the input source with signals is only selected or not. On Off Language Select one of the languages below to use for displaying the menu and messages [ : Enter setting mode] [ :Selection] [Apply: ] English/Francais/Deutsch/Italiano/Espanol/Portugues// Svenska/Turkce/Romana///Polski/ Bahasa Indonesia/Norsk/Suomi/Cestina/Magyar/......../Dansk/ Nederlands Start-up screen Sets whether the start-up screen displays when power is turned on. On Off Fan mode Sets the cooling fan speed. Standard High Lamp power Sets the lamp power. Standard Low Power on Sets whether to turn on the power when the ON/STANDBY button is pressed (Manual), or when the power cord is plugged in (Auto). Manual Auto. Detailed description [Auto input search] Automatically searches the input source that can be projected, and switches source from the connected device each time the INPUT button is pressed. If the connected device outputs no source signal, the input is skipped. When the source signal is stopped during projecting, it will switch to the other inputs automatically. If no input sources are detected, it will stop searching and “No signal” message will appear. [Fan mode] Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise gets louder.) Set this option to use the projector, for example, at high altitude (over 1,500m or 5000 ft. above sea level). [Lamp power] When [Lamp power] is set to [Low], the screen becomes a little darker, but the cooling fan noise gets quieter. [Power on] If [Power on] is set to [Auto] and there is a power outage, the projector will come on once power is restored. ¦ Displaying Information (Status display) This displays information about the input signal, lamp use time, etc. “Yes”: displayed, “No”: not displayed Item Description Computer Y/PB/PR Video S-video Input Input source name Yes Yes Yes Yes Resolution Resolution (in dots) [Note 1] Yes No No No Video mode Color method of video signal No Yes Yes Yes Picture mode Picture mode setting Yes Yes Yes Yes Lamp time Time of lamp use [Note 2] Yes Yes Yes Yes Version Firmware version [Note 3] Yes Yes Yes Yes Notes 1: The Resolution of supported RGB signals p.43 is shown. 2: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as a counter of guaranteed lamp time.) When the displayed time approaches 3,000 hours, consult with a dealer about getting a TLPLV10 replacement lamp (sold separately) prepared. 3: [Version] shows the version of the projector’s internal control program. This firmware version will be requested for customer service purposes. Note • The displayed information will not be refreshed if the status changes. To refresh the information, dismiss the display, then display it again. 36 Maintenance About lamp The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure to fully understand the following characteristics of the lamp and handle it with extreme care. • The lamp may burst with a loud noise due to impact or deterioration, or fail to light at the expiration of its life. • How long it takes before the lamp bursts or the life expires may vary greatly by lamp. Some may burst shortly after first use. • Burst is likely to happen if the lamp is used after the replacement period has elapsed. • When the lamp bursts, the broken pieces of glass may get inside the product or be released outside from the openings for ventilation. • When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along with glass dust may be released from the openings for ventilation. ¦ Immediately replace the lamp when a replacement message appears on the screen. • When the replacement time approaches, a message will appear on the screen. • The risk of burst will increase if the lamp is continuously used without being replaced. • Frequently check the used hours and prepare spares when the replacement time approaches. (...
Ce manuel est également adapté pour les modèles :Projecteurs - TDP-XP1U (2.88 mb)