Évaluations - 2, GPA: 5
(
)
)
|
Par ce dispositif a également d'autres instructions :
Projecteurs - VPL-CX63 (1.12 mb)
Projecteurs - VPL-CX63 (1.11 mb)
Facilité d'utilisation
4 Press the INPUT key to select the input source. Projecting F7 Fx Fn or and F7 Fx Fn or and Note The key used for switching the computer to output to the projector varies depending on the type of computer. 6 Adjust the upper or lower position of the picture. Use the adjuster to adjust the picture position. Using the adjuster Lift the projector while pressing the adjuster adjustment button, and adjust the tilt of the projector, then release the button at the locked position. Adjuster adjustment button Notes • When you adjust the tilt of the projector with the adjuster, the V keystone adjustment is performed at the same time. If you do not want to perform the automatic keystone adjustment, set the V Keystone menu to “Manual.” (See page 32.) If you set the “V Keystone” adjustment to “Auto,” the “V Keystone” correction is automatically adjusted. However, it may not be perfectly adjusted depending on the room temperature or the screen angle. In this case, adjust it manually. Press the KEYSTONE/TILT key on the Remote Commander to “V Keystone” displays on the screen, and adjust the value with the v/V/b/B keys. The corrected value is effective until the power is turned off. • Be careful not to let the projector down on your fingers. • Do not push hard on the top of the projector with the adjuster extended. It may cause a malfunction. 7 Adjust the size of the picture and the focus. To adjust using the Remote Commander Select the item to be adjusted by pressing the LENS key, then adjust with the v/V/b/B key. Each time you press the key, the menu toggles between Lens Focus and Lens Zoom in order. To adjust using the control panel Press the ZOOM +/– keys on the projector to adjust the size of the picture and press the FOCUS +/– keys to adjust the focus. Projecting Turning Off the Power 1 Press the ?/1 key. “POWER OFF? Please press ?/1 key again.” appears to confirm that you want to turn off the power. Note The message disappears if you press any key other than the ?/1 key, or if you do not press any key for five seconds. 2 Press the ?/1 key again. The ON/STANDBY indicator flashes in green and the fan continues to run for about 60 seconds to reduce the internal heat. Also, the ON/STANDBY indicator flashes quickly for the first 45 seconds. During this time, you will not be able to light up the ON/STANDBY indicator again with the ?/1 key. 3 Unplug the AC power cord from the wall outlet after the fan stops running and the ON/STANDBY indicator lights in red. When you cannot confirm the on- screen message When you cannot confirm the on-screen message under certain conditions, you can turn off the power by holding the ?/1 key for about two seconds instead of following steps 1 and 2. Note The internal circuitry of the Off & Go and Direct Power On/Off functions may cause the fan to continue to operate for a short time even after the ?/1 key is pressed to turn off the power and the ON/STANDBY indicator changes to red. Projecting the Picture Turning Off the Power B Convenient Functions Selecting the Menu Language You can select one of fifteen languages for displaying the menu and other on-screen displays. The factory setting is English. To change the menu language, proceed as follows: APA FREEZE KEY STONE /TILT LENS AUTO FOCUS PIC MUTING AUDIO MUTING INPUT ENTER RESET D ZOOM VOLUME MENU VPL-CX63 Front remote control detector ON/STANDBY indicator 1 Plug the AC power cord into a wall outlet. 2 Press the ?/1 key to turn on the projector. 3 Press the MENU key. The menu appears. The menu currently selected is shown as a yellow button. Selecting the Menu Language 4Press the v or V key to select the MENU SETTING menu, then press the B or ENTER key. The selected menu appears. 5Press the v or V key to select “Language,” then press the B or ENTER key. 6 Press the v, V, b or B key to select a language, then press the ENTER key. The menu changes to the selected language. To clear the menu Press the MENU key. The menu disappears automatically if a key is not pressed for one minute. Security Lock The projector is equipped with a security lock function. When you turn the power of the projector on, you are required to input the previously set password. If you do not input the correct password, you will not be able to project the picture. 3 Enter the password again to confirm. Enter new password key. Power-on cannot be performed without the password. Use: Cancel: Other key Note You will not be able to use the projector if you forget your password and the password administrator is not available. Be please aware that using the security lock can prevent valid usage in such cases. To use the security lock 1 Press the MENU key and then, on the INSTALL SETTING menu, turn on the “Security Lock” setting. 2 Enter the password. Use the MENU, v/V/b/B, and ENTER keys to enter the four-digit password. (The default initial password setting is “ENTER, ENTER, ENTER, ENTER.” After this is entered you can put in your own password. Therefore, when you use this fun...
Ce manuel est également adapté pour les modèles :Projecteurs - VPL-CX61 (1.22 mb)