Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Firmware Update – Update Firmware Note Connect for the duration of the firmware update the power adapter. Information – Display free space in the internal memory and information on the device (Capacity: / Free space: / Firmware Version / Device name: / Model / Mcu Version) Settings 19 8 Service Care Instructions for the Battery deep discharge Battery When the battery is in deep discharge or the device is not used for a longer period, proceed as followed: The capacity of the battery diminishes with time. You can prolong the life of the battery if you observe the following points: • Without a power supply, the device operates from the built-in battery. When the battery does not have sufficient capacity, the device switches to stand-by mode. Connect the device to the power supply. • When the battery does not have sufficient capacity, the battery symbol in the display turns red. • When the device is running for a long period of time, the surface becomes hot and a warning symbol appears on the projection. The device switches automatically to stand-by mode when it gets too hot. After the device has cooled down, you can continue playback by pressing any key. • Use the device at least once a week. • Charge the battery regularly. Don’t store the device with a completely discharged battery. • If the device is not used for several weeks, discharge the battery a little by using the device before storing it. • If the device only works using the USB connection or with the power supply, the battery is defective. • Keep the device and the battery away from sources of heat. DANGER! Do not replace the battery yourself Do not try to replace the battery yourself. Incorrect handling of the battery or using the wrong type of battery can cause damage to the device or cause injury. 1 Connect the USB plug to a computer, to charge the battery. Alternatively you may connect the USB plug to the power adapter (not included) (see also chapter Compatible Power Supply, page 23). The device behaves as follows: Device off Device on Connect to a computer Device turns on and off again. Slow charging Device turns on and off again. Slow charging Connect to the power adapter Device turns on and off again. Fast charging Device remains turned on. Slow charging 2 The device can be turned on and is ready to use after approximately five minutes of charging time. Battery recharge time with device off Turning on Completely possible charged Slow charging 5 minutes 10 hours Fast charging 5 minutes 3 hours Philips · PPX2240 · 2340 Cleaning DANGER! Instructions for Cleaning! Use a soft, lint-free cloth. Never use liquid or easily flammable cleansers (sprays, abrasives, polishes, alcohol, etc.). Do not allow any moisture to reach the interior of the device. Do not spray the device with any cleaning fluids. Wipe over the surfaces gently. Be careful that you do not scratch the surfaces. Cleaning the Lens Use of the projector. DANGER! brush or lens cleaning paper for cleaning the lens Do not use any liquid cleaning agents Do not use any liquid cleaning agents for cleaning the lens, to avoid damaging the coating film on the lens. Switching off the device! Switch the device on or off using the power switch before removing the power supply from the socket. DANGER! Device overheated A overheat symbol appears if the device is overheated. • At maximum level of brightness the symbol appears in the status bar and the device turns automatically to minimum level of brightness. • At minimal level of brightness the symbol shows for three seconds in the middle of the screen. Then the device turns off automatically. Service 21 1 Switch the device off using the on/off switch on the Troubleshooting side. 2 Wait at least ten seconds. Power Cycling 3 Switch the device on using the on/off switch on the If a problem occurs that cannot be corrected with the side. instructions in this user manual (see also the help 4 If the problem repeats, please contact our technical below), follow the steps given here. customer service or your retailer. Problems Solutions The Pocket Projector cannot be switched on • Connect your computer or a compatible power supply to recharge the internal battery. Make sure the Pocket Projector is switched off. No sound from the external connected device • Check the cables to the external device • Set the volume on the external device • Only the original cables from the device manufacturer may function Bad sound quality with your computer connection • Check if the audio cable is connected to the computers headphone socket or the line-out socket. • The volume setting on the computer should not be too high. Only the initial screen appears and not the image from the external device • Check if the cables are connected to the right sockets. • Please check that the external device is switched on • Check if the video output of the external device is switched on. Only the initial screen appears and not the image from the connected computer • Check if the software at y...
Ce manuel est également adapté pour les modèles :Projecteurs - PPX2340/F7 (2.31 mb)