Log:
Évaluations - 3, GPA: 4.7 ( )

Instructions Sanyo, Modèle LNS-T02K

Fabricant : Sanyo
Taille : 96.95 kb
Nom Fichier : 22dc641d-fedc-45e5-bd9d-0b3dd116b8ee.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


LNS-W02/T02 LNS-W02K/T02K Series LENS REPLACEMENT AND INSTALLATION PROCEDURE NOTES ON LENS INSTALLATION Lens installation should be performed by the qualified service personnel. It should be followed by this procedure precisely. Before attempt to install the lens, confirm the model number (both the LCD projector and the lens) and use the proper lens. If you have any questions, contact to the dealers. PARTS LIST Following parts are contained in the packing. • LENS 1 piece • LENS MOUNTING SCREWS 6 screws (2 for spare) • DRIVER 1 piece • LIGHT-BLOCK SHEET 1 sheet • LENS COVER (UPPER • LOWER ) 1 set Following checks and confirmations should be taken for safety. Check the following things by the time of the cabinet assembly after the lens installation. 1. Confirm the lens is securely fixed by 4 screws. 2. Wiring must not be tangled in the gear of the lens motor or the other mechanical part. 3. There is no missing part, or no loosing mounting part. 1AA6P1P2289-- (ICSC) LENS REPLACEMENT AND INSTALLATION PROCEDURE Perform the steps [T] to [5| for lens replacement and installation. First, set the lens at the center position with lens shift button. 1 REMOVE THE LENS COVER. First check the shape of cabinet. In case figure-1 cabinet. 1. Remove screws A (2 screws). 2. Pull down the lower lens cover while pushing the part D, then remove it. 3. Remove screws B (2 screws). 4. Remove screws C (2 screws) and remove upper lens cover. LENS COVER In case figure-2 cabinet. Remove 4 screws of the lens cover and remove the lens cover. 2 • IN CASE OF MODEL WITHOUT LENS REMOVE THE COVER PLATE OF THE LENS COVER. (See figure-3) Remove 2 screws and pull down the plate. (At the step [5|, insert the light-block sheet in the same position as the removed cover plate has been placed. Two screws are not used.) Use the light-block sheet included with lens. Set the light-block sheet, so that the large rounder side is set over the lens. LIGHT-BLOCK SHEET Fig-3 ^ Figure shown inside of the cabinet. LENS MOTOR • IN CASE OF MODEL WITH LENS REMOVE THE LENS. (See figure-4) 1. Remove the connector “K16B” of the circuit board. 2. Loosen the A, B, C wire holder and remove the lens motor lead. 3. Remove screws D (4 screws) which fastens the lens and remove the lens. Fig-4 3 INSTALL THE LENS. (See figure-4,5) 1. Remove protective caps (front and back ) on the lens. 2. Mount the lens at the lens mounting bracket with screws (4 screws) included with the lens. Use the driver included with the lens to fasten the screws . (After using, save it for latter use.) (See figure-5) 3. Connect the lens motor lead to the connector “K16B” of the circuit board. (See figure-4) 4. Fasten the lens motor lead at the A, B, C points with wire holder. (See figure-4) LENS MOUNTING BRACKET 4 INSTALL THE LIGHT-BLOCK SHEET. (See figure-6) Install the light-block sheet around the lens as shown in the illustration. (Use the sheet included with the lens.) LIGHT-BL...

Ce manuel est également adapté pour les modèles :
Projecteurs - LNS-W02K (96.95 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories