Évaluations - 2, GPA: 3
(
)
)
|
Facilité d'utilisation
TPUM-1: Tilting Pipe Adapter B. A. To adjust tilt 1. Hold A with 3/ 4” Socket 2. Loosen B with 3/ 4” Socket 3. Loosen C with 9/ 16” Socket 4. Position Display 5. Tighten A,B, & C • Designed for 26” - 55” Flat Panel • Maximum Weight Capacity: 175 • Connects to 1.5” NPT Pipe Specifications are subject to change without prior notice. Every effort has been made to provide accurate and error-free assembly and installation. Omni- Mount Systems disclaims liability for any difficulties arising from the interpretation of information contained in these instructions. If OmniMount products are used for purposes other than their original intent, OmniMount, its distributors and retailers shall not be held responsible or liable for injuries or property damage, direct, indirect, or consequential, which may arise from the inability to use this product safely, properly, and in the manner for which it has been designed and manufactured. Warranty does not apply to products which have been lost, damaged by misuse, abuse, or accident. PN —9/05 Step 8 — Attaching the Tilt- PA to the Pipe Tighten Here 1. Thread and tighten Tilting Pipe Adapter onto 1.5” NPT Pipe (not included) . 2. Tighten Tilt Tension Nut before attaching Adapter. Step 9 — Attaching the Adapter and Display to the Pipe Adapter Note: Pipe removed for clarity 4. 3. Align the space between the 4. Thread the last Nylock Nuts (2) top Nuts with the grooves in the onto the bottom two Stud Screws. Tilting Pipe Adapter and gently lower the Adapter. 5. Securely tighten all Nylock Nuts 2 11 Step 7 — Attaching the UM1 to the Display Required Tools: Ratchet and 5/16” Deep Socket or 5/16” Open Wrench or Adjustable Spanner Wrench Mounting Screw Display Spacer ( if needed) Square Washer Back Plate Large Universal Adapter Component Guide 1. Thread Mounting Screw through Square Washer, Rail, Spacer (if needed) , and into the Display’s Mounting Holes. NOTE: Ensure Retaining Screws are loose enough to allow for adjustment 2. Center the Back Plate on the Display and securely tighten the Retaining Screws and Mounting Screws Extended Rails Standard Rails Back PlateChannel Important DO NOT over tighten the mounting screws, or the display may be damaged. NEVER use a power driver to tighten the mounting screws. 10 3 Parts List ID Description Qty A Philips Screws M4 x 16mm 4 B Philips Screws M4 x 36mm 4 C Philips Screws M4 x 45mm 4 D Philips Screws M5 x 16mm 4 E Philips Screws M5 x 36mm 4 F Philips Screws M5 x 46mm 4 G Philips Screws M6 x 16mm 4 H Philips Screws M6 x 36mm 4 I Philips Screws M6 x 46mm 4 J Philips Screws M8 x 16mm 4 K Philips Screws M8 x 36mm 4 L Philips Screws M8 x 46mm 4 M 5/8" Urethane Spacer 4 N 3/4" Urethane Spacer 4 Description Qty 6mm x 12mm Screws 8 Square Washer 4 Small Hex Wrench 1 Stud Screws 4 5/16" Flange Nuts 4 5/16" Nylock Jam Nuts 4 Large Hex Wrench 1 Flange Nut Nylock Jam Nut Step 5 — Secure Sliders and Back Plate (continued) NOTE: The outer corners of the Back Plate must always be secured. Some wide Displays will require the installation of a 6mm Screw and 6mm Lock Nut (not included) to secure the Back Plate. Step 6 — Hardware Selection Consult the supplied Hardware Cross Reference list, and locate the appropriate mounting screws ( A-L) for your display Spacers Some displays will require the use of a spacer. There are two spacers provided: 5/8” (16 mm) round nose spacer (M) 3/4” (19 mm) block spacer (N) The spacers may be used individually, or may be snapped together to create one large stacked spacer. The spacers have been designed to snap directly into the mounting rail for ease in handling, and also include two different mounting holes to manage the various screw sizes. Generally, the 5/8” Spacer (M) is used on displays with slightly curved backs and/ or recessed mounting lands. The 3/4” Spacer (N) is used on displays with curved backs, and Stacked Spacers (M&N) will be used on displays with deeply curved backs and/ or protruding accessories. Step 4 — Rail Installation Step 1 — Set Studs in UM-1 Standard Configuration Narrow Configuration Step 5 — Secure Sliders and Back Plate 1. Set Rails to horizontal distance between Mounting Holes on Display. 1. Insert Stud Screws ( 4) into front of Adapter. Insert StudScrews Here 2. Thread Flange Nuts (4) onto Stud Screws and tighten using a 5/ 16” Socket. 3. Thread Nylock Nut (2) onto the two top Stud Screws leaving space between Nylock and Flange Nuts. 2. Loosely thread Slider Retaining Screws through Channels into Sliders 8 5 Step 2 — Determine Rail Selection Measure the vertical distance between Mounting Holes on Display. If distance is greater than 19” (48cm) use the supplied Extended Rails. Extended Rail Installation (only if required) 1. Using the Small Hex Wrench unscrew the Slider Retaining Screws ( 8). 2. Pull to remove the Standard Rail and attached Sliders. 3. Using the Small Hex Wrench unscrew the Rail Retaining Screws (4) and remove the Standard Rail. 4. Replace with the Extended Rail, insert the Rail R...