Évaluations - , GPA:
(
)
)
Fabricant : HP
Taille : 495.66 kb
Nom Fichier :
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Par ce dispositif a également d'autres instructions :
Logiciel - HP LeftHand P4000 Virt SAN Appliance SW 2-pk for VMware ESX Server SmartBuy Stck (77.35 kb)
Logiciel - HP LeftHand P4000 Virt SAN Appliance SW 2-pk for VMware ESX Server SmartBuy Stck (276.39 kb)
Logiciel - HP LeftHand P4000 Virt SAN Appliance SW 2-pk for VMware ESX Server SmartBuy Stck (763.44 kb)
Facilité d'utilisation
a.
Power on the other storage systems in the
again.
management group.
b.
Rediscover the storage systems in the CMC.
To allow this IP address click OK.
c.
Wait for the storage system status to become
(Note: The storage system's IP
Normal on all storage systems.
address must be on the same network
d.
Verify that the management group is
as the cluster's VIP and subnet
operating with a status of Normal. (Once all
mask.)
storage systems are up with all SAN/iQ
software services running properly, the CMC
To cancel and not change the storage
shows the management group status as
system's IP address, click Cancel.
Normal.)
5.
When the confirmation prompt opens, click OK
16. For a replacement 10 GbE board:
to confirm the TCP/IP settings change on this
If the bond was previously configured, the storage
storage system.
system should boot up with the bond configured
The CMC searches for the storage system with
using the ports in the new 10 GbE controller.
the changed IP address.
a.
Log in to the storage system using the CMC.
6.
Log in to the management group (if necessary).
b.
Navigate to the storage system Network
7.
Log in to the storage system and navigate to the
category TCP/IP tab window.
Network category TCP/IP tab window.
c.
Verify that the bond is detected and the IP
8.
Verify that the NICSlot1:Port1 interface was
address settings are valid.
assigned an IP address successfully.
9.
Select the Communication tab and verify that the
SAN/iQ Interface is set to communicate through
the NICSlot1:Port1 interface that you just
Configure the 10 GbE ports for SAN/iQ
configured.
software communication using the CMC
For each storage system in the cluster, configure the
ports as follows:
Configure the 10 GbE and 10 GbE ALB
1.
Log in to the management group, if necessary.
bond (using NICSlot:Port1 and
2.
In the CMC, select the storage system and
NICSlot:Port2)
navigate to the Network category TCP/IP tab
window.
CAUTION:
Bonding both the ports on the 10
3.
Right-click the 10 GbE port labeled NICSlot1:Port1
GbE network adapter and then using this bond
and select Edit.
for all SAN/iQ software communication could
4.
In the Edit TCP/IP Configuration window, select
pose a risk to your volume and snapshot
one of the following options to assign an IP
availability in the event of any network
address:
connectivity and/or functionality issues with the
•
Obtain an IP address automatically using the
10 GbE adapter. If you set up this bond
DHCP/BOOTP protocol
configuration, make sure you configure your
•
volumes and snapshots for 2-way or higher
Obtain a static IP Address, and manually
replication to ensure that your volumes and
assign an available IP address
snapshots remain available at all times.
If you are prompted with the following message,
click OK to continue. The condition described is
Creating the ALB bond
not actually true.
1.
Log in to the management group, if necessary.
The storage system’s IP address,
2.
Navigate to the storage system Network category
0.0.0.0, is not reachable by the
TCP/IP tab window.
cluster’s Virtual IP (VIP).
3.
If more than one bond is configured on the 1 GbE
ports, delete the second bond.
Change the storage system's IP
4.
Select the 10G ports labeled NICSlot1:Port1 and
address or cluster's VIP address
NICSlot1:Port2.
and/or subnet masks to ensure they
are on the same network. Then try
Page 5
... Ce manuel est également adapté pour les modèles :
Logiciel - HP LeftHand P4000 Virtual SAN Appliance Software for VMware ESX Server LTU (495.66 kb)
Logiciel - HP LeftHand P4000 Virtual SAN Appliance Software for VMware ESX Server Stock LTU (495.66 kb)
données dispositifs de traitement - HP StoreVirtual 4130 600GB China SAS Storage (495.66 kb)
données dispositifs de traitement - HP StoreVirtual 4130 600GB SAS Storage (495.66 kb)