Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
• Do not locate the NM200 master or remote stations in an outside wall. • Do not locate the NM200 to moisture. Doing so can create fire or shock hazards and void the warranty. • Do not place the NM200 master or remote stations in any wall cavity with any other electrical wiring in the cavity. • Install the NM200 system after the application of the wall covering material. • Do not expose the outdoor remote station speakers to significant water contact. The outdoor remote speakers are weatherproof but not water proof. Continuous direct water exposure will cause system problems. installation To ensure that the homeowner receives the high-quality music and voice reproduction that the system is designed to deliver, it is important that each step of the installation be done carefully. In the event you need troubleshooting assistance, please call our technical staff at 1-888-336-6151. The installation should be made after the application of wall covering material. Tools required: • #2 Phillips screwdriver • Standard flat head screwdriver • Wire stripper/cutter • Level Installing the Remote Stations Collect all the connectors included in the remote station packages and place them in the master rough-in for use later. At each remote station location, strip approximately 4 inches of jacket from the CAT5 wire and separate the colored conductors from one another. Strip . inch of insulation from each conductor as shown: Connect each colored conductor to its respective screw terminal. The screw terminals are marked with the appropriate wire colors. Note: Some screw terminals have more than one wire connected to them. Mount each remote station to its mounting ring using the two screws provided with each NM200 remote station CONNECTING THE IA30WH Audio Wall plate Use the labels provided to mark respective cables. Connect the cables to the IA30WH audio wall plate and mount the plate using the two screws provided. Please see figure below and refer to the NuTone IA30WH installation guide for more detailed instructions. installing the Door Stations At each door station location, strip approximately 4 inches of jacket from wire and separate colored conductors from one another. Strip . inch of insulation from conductors. Cut each shield drain wire at jacket to prevent them from touching each other. Terminate yellow and orange wires to the screw terminals on the chime pushbutton (if equipped). Connect the red and black wires to the red and black wires on the speaker respectively. Refer to figure below. Mount door station to housing using the two screws provided with the door station. NPS200WH Outdoor Remote Station At each outdoor remote station location, strip approximately 4 inches of jacket from the CAT5 wire and separate the colored conductors. Strip . inch of insulation from each conductor and connect each colored conductor together using wiring wire nuts. Note: Some wires are doubled up when connected to the remote station. Mount the outdoor remote station to the housing using the 2 screws provided with the remote station. INSTALLING THE NA300MC Volume Control At each NA300MC location strip approximately 4 inches of jacket from wires and separate colored conductors from each other. Wire nut each colored conductor to its respective wire as shown in the next figure. Connect 18 gauge speaker cable wires to the corresponding terminals of the satellite speakers. Mount the NA300MC to the single gang box using the two screws provided with the volume control. NM200 Master station Installation Gather all remote station and door station cables and cut cable ends to the same length approximately 12 inches from entry point into master rough-in. Make sure that all cables remain properly labeled. Strip approximately 2” of jacket from each of the CAT5 cables. Untwist the individual wire pairs. Insert each wire pair into the correct connector location and close connector. Please see figure below. Insert each cable connector into its proper location on the NM200 master. Make sure that the outdoor remote station is connected into the outdoor remote stations cables location only. If you are connecting two outdoor remote stations, use the screw terminal connectors provided with the NPS200 for the outdoor remote station. Connect both outdoor remote stations cables into one screw terminal connector. If the NM200 system has more than 9 remote stations, some station selector switches will control two remote stations. Do not exceed more than 15 total speakers on the system. This limitation does not include door stations. The station location can be noted on the inside of the front access panel on the left side of the NM200 master. Connect the red and black wires of the door station cables to the red and black door speaker terminals on the NM200 master as shown below. Insulate the bare wires using some of the jacket material to prevent shorting to the circuit board. Connect this wire to terminal labeled shield. Connect all orange wires from the door...
Ce manuel est également adapté pour les modèles :Téléphones filaires - NM200AL (491 kb)