Évaluations - 4, GPA: 3.8
(
)
)
|
Facilité d'utilisation
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179 HELP LINE For assistance in the use of this product, please call the following Toll-Free Help Line: 1-800-448-0329, and tell the representative that you have a Sears Craftsman Shop Phone. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. Attach your sales receipt to this booklet for future reference or jot down the date this product was purchased or received as a gift. This information will be valuable in the unlikely even that the product develops problems during the warranty period. Purchase Date:___________________________________________ Name of Store:____________________________________________ IMPORTANT SAFETY INSTRUCTIONS Some of the following information may not apply to your particular product; however, when using telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4. Telephones should not be used while you are in a bathtub, shower or pool. Immersion of the telephone or handset in water could cause an electrical shock. HANDSET, BASE AND REMOTE CHARGER LAYOUT SWITCHING BATTERY PACKS The battery packs are interchangeable. While one battery pack is charging, the other is in use. To remove the battery pack from the handset, push in on the tabs and pull. To attach the battery pack to the handset, snap the battery pack onto the bottom of the handset. INSTALLING THE PHONE CONNECTING THE TELEPHONE LINE 1. Connect one end of the telephone line cord to the LINE jack on the bottom of the base. 2. Connect the other end of the telephone line cord to a telephone jack on the wall. 3. Raise the antenna on the base. CONNECTING THE AC (ELECTRICAL) POWER 1. Plug the base into an electrical outlet. 2. Place the remote charger on a flat surface. Plug the power supply into an electrical outlet. Allow the system to charge for 16 hours prior to first use. If you don’t properly charge the phone, battery performance is compromised. INSTALLING THE BATTERY PACK 1. Detach the battery pack from the handset by pressing the side tabs. 2. Remove the "Prior to Use" tag. 3. Re-attach the battery pack to the handset. 4. Place the handset in the charge cradle on the remote charger and charge for 16 hours prior to first use. NOTE: If you don't properly charge the handset, battery performance is compromised. 5. Place the extra battery pack on the battery charge cradle on the remote charger and charge for 16 hours prior to first use. SET UP There are five programmable menus available: Language, Area Code, Ringer Tone, Tone/Pulse Dialing, and Default Setting. NOTE: To program these settings, the handset must be OFF (not in TALK mode). LANGUAGE Set the display language to show messages in either English, Spanish, or French. 1. Press the program/flash button until 1ENG 2FRA 3ESP shows in the display. 2. Use the cid/vol (+/> or -/<) buttons or the handset touchtone pad to choose 1ENG (English), 2FRA (French) or 3 ESP (Spanish). 3. Press program/flash to store selection. AREA CODE 1. Press the program/flash button until AREA CODE --- shows in the display. --- is the default setting. 2. Use the handset number pad to enter your three digit area code. NOTE: If you make a mistake, press the delete/ channel button to erase the wrong area code and repeat step 2. 3. Press program/flash to store selection. RINGER TONE You may choose from three different ringer tones. 1. Press the program/flash button until RINGERTONE shows in the display. 1 is the default setting. 2. Use the cid/vol (+/> or -/<) buttons or the handset touch-tone pad to move the arrow to 1, 2 or 3. 3. Press program/flash to store selection. TONE/PULSE DIALING Set your phone according to the type of service you are subscribed to. 1. Press the program/flash button until 1TONE 2PULSE shows in the display. 2. Use the cid/vol (+/> or -/<) buttons or the handset touch-tone pad to select 1TONE if you have touch-tone service or 2PULSE if you have rotary service. 3. Press program/flash to store selection. DEFAULT SETTING You may use the factory default settings or your own settings. 1. Press the program/flash button until DEFAULT shows in the display, NO is the default setting. 2. Use the cid/vol (+/> or -/<) buttons or the handset touch-tone pad to select NO to use your settings or YES to restore the factory default settings. 3. Press program/flash to store selection. You will hear a confirmation tone. TELEPHONE OPERATION HANDSET REGISTRATION The handset is pre-reg...