Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Installing the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Inser ting the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Testing the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Setting the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3. Keys and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4. Extra possibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Adding a function to the remote control . . . . . . . . . . . . . . . . . . . . . . . . 8 Restoring the original functions of your remote control . . . . . . . . . . . . 8 5. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 6. Need help? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Code list of all brands / equipment . . . . . . . . . . . . . . . . . . . . . . . . . 52-58 1. Introduction Congratulations on your purchase of the Philips SRU510 universal remote control. After installing the remote control it can operate the most-used functions of almost any brand of TV. You can find information about how to prepare this remote control for use in the chapter ‘Installing the remote control’. 2. Installing the remote control Inserting the batteries 1 Press the cover inwards and slide it in the direction of the arrow. 2 Place two AAA type batteries into the batter y compar tment, as shown. 3 Slide the cover back and click it firmly into place. Note: If the LED blinks four times after ever y key press, the remote control is indicating that its batteries are running low. Replace the old batteries with two new AAA batteries. Testing the remote control The remote control has been programmed to operate the most-used functions of almost any brand of TV. Because the SRU510 may use different signals for each make and even for different models of the same brand, it is advisable to test whether your TV responds to the SRU510. The example below instructs you how to do this. 1 Turn your TV on manually or use the original remote control. Tune to channel 1. 2 Check whether all the keys are working For an over view of the keys and their functions see ‘3. Keys and functions’. – If the TV responds as it should to all of the key commands the SRU510 is ready for use. • If the TV does not respond at all or not to all of the key commands, follow the instructions under ‘Setting the remote control’, or for online setup go to: 4 Instructions for use Setting the remote control This is only necessar y if your TV does not respond to the SRU510. If that is the case, the SRU510 does not recognize the brand and/or model of your TV and you need to program the remote control to do so. You can set the remote control either automatically or manually. Automatically setting the remote control The remote control will now automatically search for the right code for your device. Make sure the TV is switched on and select a channel using the original remote control or the keys on the TV (for example channel 1). The SRU510 emits the ‘switch off TV’ signal for all models of TV that are stored in the memory. Then keep keys 1 and 3 on the SRU510 pressed simultaneously for three seconds, until the LED flashes twice and then remains lit. Press and hold the Standby key of the SRU510. – The SRU510 now star ts emitting all known ‘TV off’ signals, one by one. Each time a code is sent, the LED lights up 4 When your TV switches off (stand-by), release the Standby key of the SRU510 immediately. – The SRU510 has now found a code that works on your TV. 5 Check if you can operate all functions on your TV with the SRU510. • If this is not the case, you can redo the automatic setting. The SRU510 will then search for a code that works better. – After the SRU510 has run through all the known codes, the search will stop automatically and the LED will stop flashing. – Automatic programming of a TV takes a maximum of 5 minutes. English 5 Manually setting the remote control 1 Turn on the TV manually or use the original remote control. Tune in to channel 1. 2 Look up the brand of your TV in the code list at the back of this manual. One or more four-figure codes are shown for each brand. Note the first code. On our website you can directly select your device typenumber to find the right code. 3 Keep keys 1 and 3 pressed simultaneously for three seconds until the LED flashes twice and then remains lit 4 Then enter the code noted in step 2 using the digit keys. – The LED will now flash twice and then remains lit. The code has now been stored in the memory of the SRU510. If the LED flashes once for an extended period, the code has not been entered...