Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
Press cyclone release button A to release cyclone pack. Accessing the filter Lift washable lifetime filter release button B and remove filter from machine. Washing the filter • Wash filter and case in cold water only. • Only wash blue foam and yellow cage. • Do not use detergent. • Do not put the filter in the dishwasher, washing machine, oven, tumble dryer, microwave or near an open flame CAUTION • Filter must be washed every 6 months according to instructions to maintain performance. • Turn power off and unplug before checking for blockages. Failure to do so could result in electric shock or personal injury. • Do not use detergent to clean filter. • Do not put the filter in the dishwasher, washing machine, oven, tumble dryer, microwave or near an open flame. Wash filter and case until water runs clear. Dry for at least 12 hours. Ensure filter and case are completely dry before refitting onto the machine. Washing the filter at least every 6 months B A A10480_DC14_USA_OWNER_6/3/04 1:12 PM Page 11 16 Finding blockages Important safety instructions Important safety instructions B A C D Check tools are clear of blockages. A Release wand from vacuum by pressing hose button and sliding hose off wand. Check inside wand and hose for blockages. B Press hose release button at front of machine and slide hose out with lower cord hook at rear. U bend inspection C Tilt machine forward, slide out U bend and check inside for blockages. Airway inspection D Squeeze valve release buttons and check inside for blockages. CAUTION • Turn power off and unplug before checking for blockages. Failure to do so could result in electric shock or personal injury. • If any part of your machine becomes blocked, it may overheat and then automatically shut off. Unplug machine and leave to cool down. Please note: Clearing blockages is not covered by your machine’s limited warranty. Beware of sharp objects when clearing blockages. Replace all parts of the machine before using it. If you hear a loud rachet noise it means the brushbar is obstructed. Disconnect the machine before removing the obstruction. Brushbar obstructions Lie cleaner on its front. Undo soleplate fasteners using a coin and remove soleplate. Remove lint and hair from brushbar. Replace soleplate and tighten fasteners. Ensure soleplate is fitted correctly when replacing. Finding blockages DC14 wand A10480_DC14_USA_OWNER_6/3/04 1:12 PM Page 12 Important safety instructionsImportant safety instructionsDyson Helpline contact us at 1- 866- 693- 9766 16 Changing/fitting the belt Remove wand and turn machine upside down. Changing/fitting the belt CAUTION • Turn power off, unplug machine and allow machine to cool for 1 hour before changing/ fitting belt. Failure to do so could result in electric shock or personal injury. • Ensure soleplate is in correct position before use. • Make sure all parts have been replaced securely before using your machine. A Undo fasteners using a coin, slide back end caps and remove soleplate. B Remove dirt or debris and check spindle is clean. C To replace the belt, remove the brushbar, loop belt around brushbar and feed through hole. D Check end caps are in place. A B C D 16 Changing/fitting the belt Important safety instructions Important safety instructions E Use back of cleaner as lever, loop belt around thumb. Turn the belt 90 degrees, stretch and release over spindle. Belt must be free of twists as shown. F Rest the three tabs on inside of yellow bumper strip and secure soleplate back into position. G Ensure soleplate is in correct position before use. Optional: Upholstery tool A Release catches and remove the soleplate. B Remove both brushbars and clear away thread and hair. Changing/fitting the belt C To reassemble, match the arrows on the brushbar to the arrows on central support. D Align front of soleplate with front of tool and secure all 3 catches. E Ensure slider is set as shown. CAUTION • Ensure soleplate is in correct position before use. E Optional: maintaining the Upholstery tool A B D C E A10480_DC14_USA_OWNER_6/3/04 1:12 PM Page 14 Dyson customer careImportant safety instructionsImportant safety instructionsDyson Helpline contact us at 1- 866- 693- 9766 16 Dyson customer care Do not pull on the cord. Do not place on stairs above you. Do not put your hands near the brushbar when in use. Do not use near open flame. Do not leave cleaner near heat sources. Do not pick up water or liquids. Do not run over the cord. Do not pick up burning objects. CAUTION If you have a question about your Dyson, call the Dyson helpline with your serial number (found underneath your machine). Important Information Check that your electricity supply corresponds to that shown on the rating plate. The machine must be used as rated. If the supply cord or the appliance is damaged, disconnect from the electric outlet immediately. The supply cord must be replaced by Dyson, Inc or our appointed agent to avoid a hazard. This appliance is not intended for use by young ch...