Évaluations - 4, GPA: 4.3 ( )

Fabricant : Clarke Taille : 1.49 mb Nom Fichier : Langue d'enseignement:

3. Grasp at the bearing block and pull it out from the brush housing. 4. Remove the used brush. 5. Replace the used brush roller with a new one, or clean and remove all debris at the present brush. 6. Slide back the brush into the the fixed bearing block in the brush house. 7. Push the bearing block in its position. Lock it by turning clockwise. Always disconnect the power cord before performing any machine maintenance. FILTERS - type of filter may vary from different models At these machines there are two different filters; one pre-filter before the vacuum motor and one exhaust filter. There are two different types of exhaust filters available to these machines, HEPA-filter and a standard exhaust filter. The HEPA-fi lter (High Efficiency Particulate Air filter) offers better filtration capacity then the standard exhaust filter. The exhaust filters catches any dirt that may escape from the dust bag, or motor pre filter. Replace the filter every fourth time that the dust bag is changed (more often in very dusty applications). The exhaust filters is located at the front side of the machine just above the brush house. The HEPA filter can not be cleaned or washed clean. When the HEPA-filter is clogged it must be replaced. CHANGING THE HEPA-FILTER 1. Disconnect the power cord from the electrical outlet. Push the Filter Cover Latch (19) downwards so that the cover (18) is released. Remove the filter cover from cleaner. 2. Grasp at the filter frame and remove the used and dirty HEPA-filter 3. Grasp at the filter frame and then insert the new HEPA filter to the cleaner by pushing it in place. (Do never touch the filter media at a HEPA-filter! Doing so may cause a loss of performance of the HEPA-filter). 4. Snap the Filter Cover back in place at the cleaner. 12 3 4 IMPORTANT! Never operate the cleaner without the HEPA-Filter in place at the machine. Note! These machines are not designed for picking up hazardous - i.e. poisonous dust! CHANGING THE EXHAUST FILTER 1. Disconnect the power cord from the electrical outlet. Push the Filter Cover Latch (19) downwards so that the Filter Cover (18) is released. 2. Remove the cover with the filter, from the cleaner. 3. Remove the used and dirty exhaust filter. 4. Insert a new exhaust filter to the filter cover. 5. Snap the Filter Cover back in place at the cleaner. IMPORTANT ! Never operate the machine without the Exhaust Filter in place at the machine. 12 CLEANING OR CHANGING THE PRE FILTER The pre filter catches any dirt spilled from the bag, before it can enter the vacuum motor. The filter is located below the bag. Clean the filter every third time that the bag is changed (more often in very dusty applications). To clean/replace the Pre Filter. 1. Disconnect the power cord from the electrical outlet. Then push the Dust lid button (16) in and remove the dust lid (5). 2. Grasp at the filter holder and pull the holder out from the Dust compartment. 3. Remove the dirty filter and replace with a new pre filter. The pre filter may also be washed. Wash it in warm water. Let the filter dry completely before putting it back into the filter holder. 4. This machine is also equipped with a deodorizer function (an anti smell). It.s a located in the pre filter holder. Replace it to a new deodorizer when the function begins to fade. 5. Put back the new/washed filter into the holder. Then put back the holder with filter in place at the bag housing. 6. Fit the two notches of the back cover to the two slots at the lower part of the bag housing, and push the back cover back in place at the housing. IMPORTANT ! Never operate the machine without the pre-fi lter in place. 12 35 AFTER USING THE MACHINE 1. Unplug the Power Cord from the electrical outlet. 2. If the Dust Bag Full” Indicator (15) not has been lightened during operation -the dust bag still have filling capacity. Open the dust housing cover to ensure that the dust bag not is full, replace if necessary. See also separate instructions for replacing the dust bag. Clean the bag housing, if necessary. 3. Wind up the cord (starting from the machine inlet side). 4. Store the cord at the hook at the Dust lid cover and the hook at the handle. 5. Check the brush house. Remove any built-up carpet fibers or debris from the brush and the brush housing. 6. Store the machine indoors in a clean, dry place. 34 SOMMAIRE Consignes de securite importantes........................................................... 15 Consignes de mise a la masse...................................................................16 Introduction.................................................................................................17 Pieces et entretien..................................................................................... 17 Plaque signaletique ........................................................................................ 17 Deballage de l’appareil.............................................................................. 17 Specifi catio...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :