Évaluations - , GPA: ( )

Instructions Black & Decker, Modèle AA090020D

Fabricant : Black & Decker
Taille : 365.22 kb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Seek medical attention. • The charger supplied with this product is intended to be plugged in such that it is correctly orientated in a vertical or floor mount position. WARNING: Do not look into the air vents when the unit is switched on, as sometimes there is a possibility of small debris being discharged from the air vents, especially after cleaning / replacement of the filters as debris inside the unit can be disturbed. INSTALLATION INSTRUCTIONS (FIG. B) The charging bracket can be mounted to most walls or left unattached on a flat surface. Fix the wall mount within reach of an electrical outlet. Mount securely into framing studs or wallboard using the hardware provided. Next plug power supply plug into nearby electrical outlet. Ensure cord is not too tight so as to pull unit off wall mount. WARNING: Do not mount the charging bracket directly over the electrical outlet. Excess water from the bowl could drip onto the outlet and create a hazard. RECHARGING (FIG. C) From new, the rechargable cells of the product need a minimum charge time of 16 hours to ensure full power. We suggest you fully discharge the product when it is used for the first time as this will help the cells recharge faster. The switch must be in the off (“O ) position, the product will not charge if it is in any other position. Make sure that the product is fully mounted on the charging bracket. There is anarrow on the charging base that must line up with the split of the dust bowl and thehandle. While charging, the product may get warm, this is perfectly normal and safe. It can remain on charge indefinitely without damage or danger. It is not possible to “overcharge the battery cells with the charger provided. For a better battery life, it is recommended to fully run the battery down and recharge it at least once a month. OPERATION (FIG. D) To start, slide the On/Off switch forward (i.e. “O = Off, “I = On). To stop, slide the switch back. For best performance on hard surface wet pickups, insert Squeegee into the Bowl Nozzle Opening. Do not fill the bowl beyond the end of the intake chute. If there is any liquid in the bowl, do not turn the unit upside down, sideways, point the nozzle upward, or shake the vac excessively. After picking up liquid substances clean the vac and filter immediately. Mold and mildew may form if the unit is not properly cleaned after wet pickups. Always return the product to the power supply immediately after use so that it will be readyand fully charged for the next use. Ensure that the product is fully engaged with the power supply plug. CLEANING THE PRODUCT (FIGS . E-I) WARNING: Never use the Dustbuster without its filters. NOTE: The filters are re-usable, do not confuse them with disposable dust bags, and do notthrow them away when the product is emptied. We recommend that you replace the filters every 6-9 months depending on frequency of use. FIG. E Remove the dust bowl by turning it counterclockwise slightly and pulling it away from the handle. To replace the bowl, place it back onto the handle and twist it clockwise until it “clicks firmly into position. FIG. F Empty the dust from the bowl and wash if necessary (see Fig. H). FIG. G While holding the bowl over a wastebasket, pull out the foam filter and hard filterto empty the contents of the bowl. FIG. H Wash the filter regularly using warm, soapy water and ensure that it is completelydry before using it again. The cleaner the filters are, the better the product will perform. It is very important that the filter is correctly in position before use. The dust bowl can also be washed in warm soapy water. Ensure that it is dry before re-attaching. IMPORTANT: Maximum dust collection will only be obtained with clean filters and an empty dust bowl. If dust begins to fall back out of the product after it is switched off, this indicates that the bowl is full and requires emptying. FIG. I Never immerse the product in water. A damp cloth and soapy water should be used to clean the exterior of the motor section. Always ensure the product is completely dry before re-use or storing. ECONOMIC USAGE • Your product is very economical to charge. While it is charging it uses less than half the amount of electricity used by a light bulb. • When fully charged, the average effective usage times are between 8-10 minutes. • It may take sever...