Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
This is recommended every 10-15 tankfulls, to free up any scale deposits from the tank. Fill the boiler with 8 oz. (125 ml) of water and shake the cleaner vigorously. Tilt the cleaner upside down to empty the boiler of water and any scale deposits. Descaling Your Steam CleanerIf the tap water in you area contains a high level of calcium depositsand you have been using tap water to do your steam cleaning, you should descale your unit after 10-15 tankfulls. 1. Unplug the steam cleaner from the power source before you descalethe boiler. Allow the unit to cool. 2. Fill the boiler with 1 part vinegar and 5 parts water and leave overnight or for a period of approximately 8 hours. Do not screw the safety cap onto the steam cleaner while you are descaling the boiler. Do not use the steam cleaner while descaling solution is inside the boiler. 3. After the period of soaking, turn the steam cleaner upside down to empty solution from the boiler. Due to the fact that a small amount of solution will be left in the boiler, it is necessary to rinse the boiler out with clean water 2 or 3 times. Your steam cleaner is now ready for use. To Descalethe Steam CleanerCare and Maintenance Components On/Off Power Switch: The On/Off switch has a light that wil illuminate when the unit is plugged into the 120V wall outlet and the switch turned to the “On” position. Steam Ready Light: The steam ready light located on the handle wil turn “On” when the steam is ready. Caution: Read the instructions for “Filling the Water Tank” before opening the Safety Cap. Caution: Always unplug before filling. ALLOW UNIT TO COOL FOR FIFTEEN (15) MINUTES BEFORE REFILLING. Important: Do NOTadd cleaning solutions, scented perfumes, oils or any other chemicals to the boiler in this appliance. Use tap water or distilled water if the tap water in your area is very hard. 5 Important: When using the steam cleaner with the shoulder strap, avoid rocking or tilting the unit excessively as this may cause water to enter the hose and be discharged along with the steam. 8 Attaching the Shoulder Strap Using the detachable shoulder strap allows for greater freedom of movement when both hands are needed for various cleaning tasks. To attach the shoulder strap to the steam cleaner, simply snap the shoulder strap hooks onto the connecting rings on the unit body. (Fig. 9, 10 & 11) Fig. 11 Fig. 10 OPERATING INSTRUCTIONSFilling or Refilling Your Steam Cleaner With WaterImportant: Always insure that the unit is “UNPLUGGED” from the wall receptacle prior to initial filling or re-filling the water tank and has been allowed to cool for 15 minutes. Never attempt to fill this unit under awater tap, always use the filling funnelprovided. 1. Remove the plug from the electrical outlet and allow the steam cleaner to cool for fifteen (15) minutes. 2. Press the steam trigger on the hand grip to vent any residual steam pressure that is in the boiler. 3. Place the unit on a flat, stable surface. Push down firmly on the safety cap and slowly turn the safety cap counter clockwise until it is removed. 4. Place the funnel in the tank opening. (Fig. 1) Fill with a maximum of one filling flask or 2 cups (500 ml) of water. Do Not Overfill. Turn the safety cap clockwise to replace. Note: To remove or replace the safety cap, push down on it firmly and rotate it clockwise to tighten or counter clock- wise to loosen. If not depressed the cap will rotate freely without advancing. Note: Filling the unit with hot water will shorten the heat up time. Warning: Extreme care should be taken when refilling the unit. Allow unit to cool for 15minutes and vent any residual steam pressure (see Step #2) from the boiler before refilling. When refilling the steam cleaner while the boiler is still hot, there is a risk that water will squirt back during filling and cause scalding. Use caution when opening the Safety Cap as cap may become hot during use and escaping steam can cause scalding. 5. Connect desired attachments onto the flexible steam hose. 6. Plug the unit into a standard ( 120 volt, grounded) wall receptacle and switch the On/Off switch to the “On” position. Allow approximately 4-6 minutes for vapor to reach its working temperature and pressure. When the unit is ready for use, the steam ready light will turn “On” . Always point nozzle outlet in a safe direction. At the start, some water will come out from the nozzle. This is normal. Note: When the steam cleaner has run out of water, steam output will cease. 7. When finished using the unit, turn it “Off” and unplug it from the electrical outlet.Warning: This appliance is under pressure. After every use, press steam trigger button until all pressure has been released before removing safety cap. Allow unit to cool for fifteen (15) minutes before refilling. Fig. 1 Text Box: OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Fig. 8ConnectingpointsConnectingpointsFig. 9 Note: Fit the steam pocket frame with the angle adapter onto the extension tube. Step 2. If the...