Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
2. Remove the tank from the base of the machine by lifting the tank carry handle. Measuring Cup Carry Handle ATTENTION: Some Berber carpets have a tendency to fuzz with wear. Repeated strokes in the samearea with an ordinary vacuum or deep cleaner may aggravate thiscondition. 2 4' 3' 1 3 4 5 6 7 9101112 EXIT STARTHERE 1. 2. Handle Release Lever 800.237.7691 6 ug120-4072_1370-1622_908.indd 6 10/14/08 12:55:15 PM 4. 3. OperationFill the 2-in-1 water tank (continued) 3. Carry like a bucket to the sink. Rotate the handle forward to unlatch the lid. Remove lid, turn over and locate built in measuring cup. 4. Fill formula to the indicated fill line on the built in measuring cup and pour into mouth of the bladder. 5. 6. If using BISSELL 3X Concentrate formulas: add one formula capful directly into the mouth of the bladder. 5. Fill up the bladder with clean hot tap water. *Do not boil or microwave water as it can destroy the bladder. 6. Replace the top of the tank by matching 7. the lid and tank edges. Handle must be in the forward position in order to replace lid. Rotate the handle to the carrying position to latch the lid. Note: Remember to secure the lid and test to make sure it is secure before picking up the tank. 7. Place tank into machine base, seating firmly in place. Rotate tank handle back into latched position. Bring machine handle back into upright position. Carpet cleaning strokes 1. Plug the deep cleaner into a proper outlet and turn the power switch ON ( I ). The switch is located on the back of the unit. 2. With your foot, press the handle release lever on the back of the lower body of unit. 3. While pressing the spray trigger, make one slow forward wet pass and another back. Let the BISSELL advanced deep cleaning formula and DirtLifter PowerBrush do the work for you. Caution: Do not over wet. 4. Release the spray trigger and make one slow forward and backward pass over the same area to remove any residual dirty water and aid in drying. 5. Repeat cleaning passes until solution being pulled up appears clean. Continue passes without pressing the trigger until you can’t see any more water being suctioned up. Tip: Thorough vacuuming before deep cleaning will prevent early clogging of the lint trap. WARNING: To reduce the risk of fire and electric shock due to internal component damage, use only BISSELLcleaning fluids intended foruse with the deep cleaner. Non-BISSELL cleaning solutions may harm themachine and void the warranty. 800.237.7691 7 ug120-4072_1370-1622_908.indd 7 10/14/08 12:55:16 PM Operation 2. Empty the 2-in-1 water tank/ clean removable nozzle 1. Turn power switch OFF (O). Remove the 2-in-1 water tank from the base using the tank carry handle. Carry the tank like a bucket to a utility sink or outside where you will dispose of the collection water. Remove the top of the tank by rotating the handle forward to unlatch lid and lifting lid off tank. 2. Empty collection water from bottom of tank. 3. After each use, remove and rinse the lint 3. 4. screen located on the tank lid. 4. If nozzle needs to be rinsed:remove by grasping handle at top and pulling forward.Clean removable nozzle by rinsing under running water. 5. When finished replace nozzle by slightly raising front of machine to line up slots on the base of the machine with the hooks on nozzle. Attach at base first and then click nozzle into place. NOTE: If nozzle is not attached properly loss of suction will occur. 6. To continue carpet cleaning refer back to pages 6 through 8, beginning with “Fill the 2-in-1 water tank” on page 6. If cleaning is complete, refer to the “Maintenance and care” section on below. Maintenance and care Machine care For best results, a few simple steps can assure your machine is well maintained after your cleaning is complete. 1. Turn power switch OFF (O). Unplug the machine and wrap the power cord. 2. After emptying the 2-in-1 water tank, rinse it out at a faucet with running hot tap water, taking care to clean underneath and around the heavy duty bladder. Clean out red lint screen. Removable nozzle may be rinsed if necessary. 3. Replace the 2-in-1 water tank on the machine. 4. Any loose hair or debris can be pulled from the brush roll if desired and thrown away. 5. Wipe the machine’s exterior with a soft cloth. 6. After carpet is dry, vacuum again to remove hair and fuzz. 800.237.7691 1. Lint Screen 5. 8 ug120-4072_1370-1622_908.indd 8 10/14/08 12:55:17 PM be stored where there is a danger of freezing. Freezing will damage internal components and void the warranty. Machine storage Put the unit away in a closet or basement for the next use. Store cleaner in a protected, dry area. Since this product uses water, it must not Maintenance and care WARNING: To reduce the risk of fire, electric shock or injury, unplug from the outlet before servicing. Troubleshooting Reduced Spray OR No Spray Possible cause Remedies 1. Bladder may be empty 1. Turn power switch OFF (O);...
Ce manuel est également adapté pour les modèles :Aspirateurs - POWERSTEAMER 1622 (558.47 kb)