Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
Thoroughly inspect all material to be shredded and remove any metal, rocks, bottles, cans, or other foreign objects which could cause personal injury or damage to the machine. 4. If the impeller strikes a foreign object or if your machine should start making an unusual noise or vibration, immediately shut the engine off. Allow the impeller to come to a complete stop. Disconnect the spark plug wire, ground it against the engine and perform the following steps: a. Inspect for damage. b. Repair or replace any damaged parts. c. Check for any loose parts and tighten to assure continued safe operation. 5. Do not allow an accumulation of processed material to build up in the discharge area. This can prevent proper discharge and result in kickback of material through the feed opening. 6. Do not attempt to shred or chip material larger than specified on the machine or in this manual. Personal injury or machine damage could result. 7. Never attempt to unclog either the feed intake or discharge opening while the engine is running. Shut the engine off, wait until all moving parts have stopped, disconnect the spark plug wire and ground it against the engine before clearing debris. 8. Never operate without vacuum bag and discharge chute properly attached to the machine. Never empty or change vacuum bag while the engine is running. Rear end of vacuum bag must be kept closed at all times during operation. 9. Never operate without either the inlet nozzle or optional hose attachment properly attached to the machine. Never attempt to attach or change either attachment while the engine is running. 10. Keep all guards, deflectors and safety devices in place and operating properly. 11. Keep your face and body back and to the side of the chipper chute while feeding material into the machine to avoid accidental kickback injuries. 12. Never operate this machine without good visibility or light. Always be sure of your footing and keep a firm hold on the handles. 13. Do not operate this machine on a gravel surface. 14. Do not operate this machine while under the influence of alcohol or drugs. 15. Muffler and engine become hot and can cause a burn. Do not touch. 16. Never pick up or carry machine while the engine is running. MAINTENANCE AND STORAGE 1. Never tamper with safety devices. Check their proper operation regularly. 2. Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage and repair, if needed. 3. Before cleaning, repairing, or inspecting, stop the engine and make certain the impeller and all moving parts have stopped. Disconnect the spark plug wire and ground it against the engine to prevent unintended starting. 4. Do not change the engine governor settings or overspeed the engine. The governor controls the maximum safe operating speed of the engine. 5. Maintain or replace safety and instruction labels, as necessary. 6. Follow this manual for safe loading, unloading, transporting, and storage of this machine. 7. Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer, etc. 8. Always refer to the operator’s manual for proper instructions on off-season storage. 9. If the fuel tank has to be drained, do this outdoors. 10. Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment. 4 5 Figure 1 IMPORTANT: This unit is shipped without gasoline or oil in the engine. After assembly, see OPERATION section of this manual for proper fuel and engine oil fill-up. NOTE: Reference to right and left hand side of the Yard Vacuum is observed from the operating position. See Figure 1. This Yard Vacuum has been completely assembled at the factory, except for the handle, bag, and blower chute. These parts are shipped loose in the carton. A pair of safety glasses and a 20-oz. bottle of engine oil are also included in the carton. See Figure 1. REMOVING UNIT FROM CARTON • Cut the corners of the carton. • Remove all loose parts. • Remove packing material. • Lift unit from the rear to discard packing material from under unit and roll unit out of carton. • Check carton thoroughly for any other loose parts. LOOSE PARTS IN CARTON (See Figure 1) • Handle Assembly • Hose Assembly • Bag • Blower Chute • Safety Glasses (Not Shown) • A 20-oz. Bottle of Engine Oil (may be located in bag) • Operator’s Manual DISCONNECTING SPARK PLUG Before proceeding with assembly of your new Yard Vacuum, disconnect the spark plug wire from the spark plug and ground onto the retaining post on the engine. This will prevent accidental starting of the engine. See Figure 2. Figure 2 ATTACHING THE HANDLE • Unfold the upper handle until it aligns with lower handle. Make sure the rope guide is on the right side of upper handle. See Figure 1. 20-oz. Bottle of Engine Oil Blower Chute Upper Handle Rope Guide Wing Nut Wing Nuts Lower Handle Wing Nuts Carriage Scre...