Évaluations - 4, GPA: 4.5
(
)
)
|
Facilité d'utilisation
The green power light should come on. 6. Within a few seconds, the Parent Unit will lock on to the Nursery Unit and the top four (4) green LEDs will shut off. A second later, you will hear a series of beeps and the connection LED should change from red to green. Your monitor is now ready for use. 7. If the top four (4) LEDs do not shut off, power off the Parent Unit and the Nursery Unit and repeat steps 4 and 5 above. 8. If the connection LED on the Parent Unit does not change from red to green and the unit begins to beep, press the channel “ch” button on the Nursery Unit. Within a few seconds, the Parent Unit should lock in on the Nursery Unit and the connection LED should change from red to green. You may hear an audible beep during this process. 9. If the Parent Unit is still unable to lock in on the Nursery Unit (connection LED will be red and the unit will beep), power down both the Parent Unit and the Nursery Unit. Wait for 10 seconds then hold the volume down button on the Parent Unit while pressing the On/Off switch. When the unit powers up, you will hear a single beep and all of the soundlights will illuminate. Release the volume down switch and within 2 seconds you will hear two beeps and all of the Sound Light LEDs will stay lit and the bottom LED will be red. 10. Repeat steps 5 & 6 above. 11. Repeat same set-up procedure if your system has two Parent Units. 4 Testing the System Testing the System It is VERY IMPORTANT to test the system when first set up, and at regular times thereafter. Test the units if you suspect they may have been damaged or have not been used for a long time. 1. If two adults are present, have one take the Parent Units to different locations, trying various volume settings, while the other speaks into the Nursery Unit. 2. If only one adult is available, place a ticking clock, radio, or other sound-producing device near the Nursery Unit to test it. 3. When testing, keep the level of your child’s sounds in mind, and adjust the volume accordingly. 4. If there is sound interference, switch the Nursery Unit and the Parent Units to the other channel setting. Operation To Listen To Baby • Turn on Nursery Unit using the ON/OFF switch. • Turn on one or both Parent Units using the ON/OFF switch. • Adjust the volume on the Parent Unit by pressing the Volume Up/Down buttons. Note that the Sound Lights LEDs illuminate as the volume button is pressed up or down to provide a visual feedback for the volume level. The unit will beep louder or softer depending on the volume level. • The Sound Lights on the Parent Unit will illuminate as your child (or other objects) make noise near the Nursery Unit. Please note that the Sound Lights and volume control on the Parent Unit are independent of each other. With the volume turned all the way down, the Sound Lights will still illuminate as your child (or other objects) make noise near the Nursery Unit. Parent Finder Feature • Some units come equipped with a Parent Finder feature. This feature will allow you to locate a misplaced Parent Unit as long as the Parent Unit is powered on and within range of the Nursery Unit. • To activate, press the “PF” button on the side of the Nursery Unit (the Nursery Unit needs to be ON). • The Parent Unit will generate an audible beep every second and the soundlights will flash on and off. • Once the Parent Unit is located, the audible beep can be shut-off by pressing any button on the Parent Unit. TroubleShooting DO NOT ATTEMPT to modify the unit. Any modifications to the transmitter and/or receiver can void the operator’s authority to operate the equipment. Most problems have a simple solution. First, check that: • Power is turned ON for both units • Both units are plugged in (or batteries are fresh in Nursery Unit and fully charged in Parent Unit) • Electrical outlet works • Volume is turned up on Parent Unit • Parent Unit is in range of the Nursery Unit No Sound • Battery dead or weak — replace or use AC adapter. • AC adapter not properly connected — check the connections. • Nursery Unit covered or blocked — remove the obstruction. Weak Sound • Nursery Unit too far from baby — move closer. • Large objects blocking the signal — try repositioning Nursery Unit. • Volume setting too low — turn it up. Static • Interference from other electrical equipment — eliminate cause of static (TVs, mixers, computers, fans, fluorescent lights, light dimmers, etc.) • Parent Unit too far from Nursery Unit — move them closer. • Significant amount of obstructions between Parent Unit and Nursery Unit such as walls, ceilings & buildings. Try moving the Nursery Unit to another part of the room. • Change channel on Nursery Unit. Shrill Sound (Feedback) • Nursery Unit and Parent Unit too close together — move them farther apart. • Volume set too high — lower the volume. 5 6 Piezas de repuesto • Informacion sobre la garantia (EE.UU.) Registro del producto (EE.UU.) Piezas de repuesto • Informacion sobre la garantia (EE.UU.) Registro del pro...
Ce manuel est également adapté pour les modèles :Bébé - 2791 (233.96 kb)