Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
when the LINK light on the parent unit lights up green continuously. Briefly press the SENSITIVITY button on the parent unit (Fig. 18). The sound level lights on the parent unit light up for approx. seconds to indicate the , current sensitivity level. 10 EngliSh Briefly press the volume + and – buttons on the parent unit until the desired microphone sensitivity level for the baby unit has been reached. Note: If you press the SENSITIVITY button and/or the volume + and – buttons too long, the microphone sensitivity is not adjusted. -one light on = minimum sensitivity level -all lights on = maximum sensitivity level Note:When the microphone sensitivity of the baby unit is set to a high level, it picks up more sounds and therefore transmits more often. As a result, the units consume more power. talk function You can use the TALK button on the parent unit to talk to your baby (e.g. to comfor t your baby). 1 Press and hold the TALK button and talk clearly into the microphone (Fig. 19). Release the TALK button when you have finished talking. Note:When you press the TALK button, you can no longer hear your baby. Silent baby monitoring 1 Briefly press the volume down (–) button on the parent unit until the volume is switched off completely (Fig. 0). The volume is completely switched off when all sound level lights are out. As long as the baby unit does not detect a sound, all sound level lights on the parent unit are , out (Fig. 1). When the baby unit picks up a sound, one or more sound level lights on the parent unit , come on.The louder the sound, the more lights come on. nightlight 1 Briefly press the nightlight button Q on the baby unit to switch on the nightlight. (Fig. ) Press the nightlight button Q again briefly to switch off the nightlight. The nightlight dims gradually before it goes out completely. , Note: If you press the nightlight button Q too long, the nightlight does not come on or go out. Tip: Switch off the nightlight when you operate the baby unit on batteries.This saves power. paging the parent unit If you have misplaced the parent unit and its volume is switched off, you can use the PAGE button on the baby unit to locate the parent unit. 1 Briefly press the PAGE button on the baby unit (Fig. 23). The parent unit automatically resets to medium volume level and produces a paging alert , tone. To stop the paging alert tone, press the PAGE button again briefly or press any button on the parent unit. Note: If you press the PAGE button too long, the parent unit does not produce the paging alert tone. Belt clip and neck strap If the batteries of the parent unit are sufficiently charged, you can take the unit with you inside and outside the house if you attach the unit to your belt or waistband with the belt clip or if you hang it round your neck with the neck strap.This allows you to monitor your baby while you are moving around. EngliSh 11 1 1 1 1 Connecting the belt clip Insert the small pin on the back of the belt clip into the opening on the back of the parent unit (1).Turn the belt clip to the left ( ) until it locks into position (‘click’) (Fig. ). Disconnecting the belt clip Turn the belt clip to the right (1) and take it out of the opening ( ) (Fig. 5). Connecting the neck strap Insert the small pin at the end of the neck strap into the opening on the back of the parent unit (1).Turn the neck strap to the left ( ) until it locks into position (‘click’) (Fig. 6). Disconnecting the neck strap Turn the neck strap to the right (1) and take it out of the opening ( ) (Fig. 7). reset function This function allows you to reset the parent unit and baby unit to the default settings.You can use this function if problems occur that cannot be solved by following the suggestions in chapter ‘Frequently asked questions’.You have to reset each unit separately. 1 Press and hold the on/off button 3 for seconds to switch on the unit. (Fig. 11) Then immediately press and hold the volume down (-) button until the appliance beeps. (Fig. 8) The unit has now been reset to the default factory settings. , Now do the same for the other unit. Default settings Parent unit -Loudspeaker volume: 1 -Microphone sensitivity: 3 Baby unit -Loudspeaker volume: 3 -Nightlight: off Cleaning and maintenance Do not immerse the parent unit and the baby unit in water and do not clean them under the tap. Do not use a cleaning spray and/or liquid cleaners. 1 Unplug the baby unit if it is connected to the mains and take the parent unit out of the charger. Clean the parent unit and the baby unit with a damp cloth. Storage You can use the travel pouch to store the baby monitor while you travel. , When you are not going to use the baby monitor for some time, remove the batteries and , store the parent unit, the baby unit and the adapters in the travel pouch supplied. Environment Do not throw away the appliance with the normal household waste at the end of its life, but , hand it in at an official collection point for recycling. By doing this, yo...