Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
EngliSh 11 preparing for use Baby unit You can run the baby unit on outlet electricity or on non-rechargeable batteries. Even if you are going to operate the unit on outlet electricity, we advise you to inser t non-rechargeable batteries. This guarantees automatic back-up in case of power failure. operation on outlet electricity 1 , Put the large appliance plug in the baby unit and put the adapter in a wall outlet (Fig. ). The power-on light goes on. operation on non-rechargeable batteries The baby unit runs on four 1.5V R6 AA batteries (not included). We strongly advise you to use Philips LR6 PowerLife batteries. Do not use rechargeable batteries, as the baby unit does not have a charging function. Unplug the baby unit and make sure your hands and the unit are dry when you insert the non- rechargeable batteries. 1 Remove the lid of the compartment for non-rechargeable batteries. (Fig. ) Insert four non-rechargeable batteries (Fig. 5). Note: Make sure the + and - poles point in the right direction. Reattach the lid. (Fig. ) parent unit operation on rechargeable battery pack The parent unit comes with a rechargeable Li-Ion 1000mAh batter y pack. Charge the parent unit before you use it for the first time or when the parent unit indicates that the batter y is low (the empty batter y symbol flashes on the display and the parent unit beeps).The parent unit star ts indicating that the batter y pack is low 30 minutes before the batter y pack is completely empty. Note: If the rechargeable battery pack is completely empty, the parent unit automatically switches off and loses contact with the baby unit. 1 Remove the lid of the compartment for the rechargeable battery pack (Fig. ). Insert the rechargeable battery pack (Fig. 8). Reattach the lid (Fig. ). Insert the small appliance plug into the charger, put the adapter in a wall outlet and place the parent unit in the charger (Fig. 10). The charging light on the charger goes on. , The display shows a charging battery symbol to indicate that the parent unit is charging. ,5 Leave the parent unit in the charger until the battery pack is fully charged. During charging, the charging light on the charger lights up continuously. , When the battery pack is fully charged, the display of the parent unit shows a full battery , symbol T. -When you charge the parent unit for the first time or after a long period of disuse, switch it off and let it charge continuously for at least 10 hours. -Charging normally takes 4 hours, but it takes longer when the parent unit is switched on while charging.To keep the charging time as shor t as possible, switch off the parent unit during charging. 1 EngliSh -When the batter y pack is fully charged, the parent unit can be used cordlessly for at least 24 hours. Note:When the parent unit is charged for the first time, the operating time is less than 24 hours.The battery pack only reaches its full capacity after you have charged and discharged it four times. Note:When the parent unit is not in the charger, the battery pack gradually discharges, even when the parent unit is switched off. Using the appliance 1 Place the parent unit and the baby unit in the same room to test the connection (Fig. 11). Make sure the baby unit is at least 1 metre/3 feet away from the parent unit. Press and hold the on/off button 3 on the baby unit until the green power-on light goes on. (Fig. 1 ) Note:The power-on light always lights up green, even when there is no connection with the parent unit. The nightlight lights up briefly and then fades out again. , The display lights up and the battery symbol appears on the display (Fig. 1 ). , After seconds the temperature and humidity values are shown on the display (Fig. 1 ). , Press and hold the on/off button 3 on the parent unit until the sound level lights light up briefly. (Fig. 15) ,, , , , , The display goes on and the battery symbol appears on the display (Fig. 1 ). The LINK light flashes red and the message ‘Searching’ appears on the display. (Fig. 17) The LINK light on the parent unit turns green and lights up continuously when a connection has been established between the baby unit and parent unit.The message ‘Linked’ appears on the display. (Fig. 18) After 2 seconds the message ‘Linked’ disappears and the temperature and humidity values are shown on the display. (Fig. 1 ) The first time you switch on the parent unit, the message ‘Language’ appears on the display. Select the desired language (see chapter ‘Menu options, section ‘Setting display language’). (Fig. 0) If no connection is established, the LINK light on the parent unit stops flashing and lights up red.The parent unit beeps from time to time and the message ‘Not Linked’ appears on the display. (Fig. 1) positioning the baby monitor 1 Place the baby unit at least feet/1 meter away from your baby (Fig. ). Place the parent unit within the operating range of the baby unit. Make sure it is at least feet/1 meter away from the baby unit to avoid acoustic feedback ...