Évaluations - , GPA:
(
)
)
Fabricant : Philips
Taille : 8.13 mb
Nom Fichier :
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
Depending on your local circumstances the operating range can decrease down to approximately 50 metres (maximum). When approaching the outer range boundary, the Parent Unit may produce a scratching or interrupting sound. The system check function (lights 3, 21 and beeping sound on the Parent unit) will in principle indicate to you the reliability of the connection between the Parent unit and Baby unit and whether you are out of range. ENGLISH 15 Problem solving If a fault occurs, first check the points listed below. If you are unable to remedy a problem by following these hints, contact the helpline or consult your dealer. Under no circumstances should you tr y to repair the set yourself as this will invalidate the guarantee. Problem Possible cause Solution DECT SYSTEM LINK light does not light Parent Unit: unit is not turned on. Baby Unit: unit is not turned on. Batteries are low. Power adapter is not plugged in or batteries are exhausted. Rechargeable batteries not inser ted into Parent Unit. Press the Abutton (26). Press the Abutton (7) Replace/recharge batteries. Plug in power adapter or replace batteries. Place rechargeable batteries. High pitched noise Units are too close to each other. Volume too high. Move Parent Unit away from Baby Unit. Decrease the Parent Unit volume. Parent Unit batteries do not charge Batter y life is at an end. Batter y polarity misfitted. Poor contact between Unit and Charger. Replace rechargeable batteries, using only NiMH rechargeable batteries. Fit batter y in correct polarity position. Clean Charger contact with soft dr y cloth. No sound/ Cry of baby is not heard Volume on Parent Unit is set too low. Sensitivity setting on Parent Unit too low. Units are out of range. Increase Parent Unit volume. Adjust sensitivity level of Parent Unit. Move Parent Unit closer to Baby Unit. Parent unit reacts on other ambient sounds Ambient sounds other than the baby, trigger the transmission. Move the Baby Unit closer to the baby and tr y lowering the sensitivity on the Parent Unit. Battery check light lights (Baby Unit) or blinks (Parent Unit) Batteries are low or empty. Parent Unit: Baby Unit: Recharge or replace batteries. Replace or remove batter y. DECT SYSTEM LINK light (flashing red)/ System check alarm beeps on Parent Unit Units too far away from each other. Batteries are low. Units cannot establish a connection, even when close to each other. No power to one of both units. Decrease distance between units. Replace/recharge batteries. Try solving the problem by using the factor y initialisation mode. For this see chapter ‘Factory Initialisation mode’. Check Abutton (26) on Parent Unit and Abutton (7) on Baby Unit. Technical specifications Power supply: – 2x AA rechargeable batteries (1.5V, NiMH, 1600mAH) for Parent Unit (included) – Optional batteries 4x 1.5V; AA for Baby Unit (not included) – AC power adapter 230V AC, 50 Hz. Only use the 9 Volt DC/ 300 mA AC power adapter included. Operating temperature: 0 °C to 40 °C Standard: Digital Enhanced Cordless Telecommunications (DECT) Resetting to default factory settings Factory Initialisation mode With this mode both units can be reset to the default factory settings. Factory Initialisation can be used if problems occur which can not be solved by following the suggestions in chapter ‘Problem solving’. Resetting must be done separately for each unit. 1 Press and hold the A button (7 and 26) to switch on the unit. 16 ENGLISH SC486_book.qxd 23-09-2004 18:22 Pagina 16 2 When the lights on the unit light up, immediately press and hold the volume down button ( - 13 and - 18). > The unit has now been reset to the default factory settings. Note: By executing the factory initialisation mode Parent Volume, Baby Volume and Baby Sensitivity are automatically reset to their factory default settings. Personal preferences need to be set again. Factory default settings are: – Parent Unit Volume: level 1 (Volume 9) – Baby Unit Volume: level 3 (Volume 9 9 9) – Baby Unit Sensitivity: level 5 (Sensitivity 9 9 9 9 9) Need Help? In case you have any questions about the SBC SC486, please contact our helpline for assistance! You can find the number in the list on page 2. Before you call, please read this manual carefully. You will be able to solve most of your problems. The model number of the baby monitor is SBC SC486. Date of purchase: _____ /_____ /______ day /month /year + – + – ENGLISH 17 SC486_book.qxd 23-09-2004 18:22 Pagina 17 Guarantuee certificate Certificat de garantie Garantieschein Garantiebewijs Certificado de garantia Certificato di garanzia Certificado de garantia ( Garanticertifikat Garantibevis Garantibevis Takuutodistus 1 1 year warranty % annee garantie ar garanti Jahr Garantie ar garanti jaar garantie ar garanti ano garantia vuosi takuu anno garanzia ano garantia Type: SBC SC486 Serial nr: _____________________________________________________________ Date of purchase - Date de la vente - Verkaufsdatum - Aankoopdatum - Fecha de compra ...