• Do not attempt to recharge a non-rechargeable battery. • A rechargeable battery CANNOT be recharged by plugging the AC adapter into the Nursery Unit. • Remove the batteries from the unit if it is no longer being used or will be stored for an extended period of time. Battery Installation Using AC Adapters + - + -+ - Plug in cord Parent Unit • The battery must be plugged into the Parent Unit before the unit will be ready for use. Remove the battery door cover on the Parent Unit with a key or flat blade screw driver. Remove the battery pack from the packaging and plug into the back of the unit. Place the battery pack into the recess and press the wire into the slot on the side. Replace the battery door. Nursery Unit • Turn the unit over, and use screw driver to remove the battery door. • Place 3-AAA (1.5V-LR03) batteries into the battery compartment. Note the proper orientation of the batteries. • Place the battery door back on the unit and fasten the screw. • Please remove a dead battery promptly. A dead battery left in the unit may leak, damaging your unit. • Do not attempt to recharge a non-rechargeable battery. • A rechargeable battery CANNOT be recharged by plugging the AC adapter into the Nursery Unit. • Remove the batteries from the unit if it is no longer being used or will be stored for an extended period of time. Battery Installation Using AC Adapters + - + -+ - Plug in cord • The Parent Unit can use either the rechargeable battery that comes with the unit or standard 120 volt AC household current. The Nursery Unit uses 3-AAA (1.5V-LR03) batteries or standard 120 volt AC household current. • To use AC adapters, plug the connector on the cord into the AC adapter jack on the side of the Parent Unit (under the rubber cover) or the back of the Nursery Unit. If using the Docking Station, plug the AC adapter connector into the back of the Docking Station. The Parent Unit may now be placed in the Docking Station. Then plug the adapter into a standard wall outlet. • Use ONLY the Graco adapters included with the unit. Do not use these adapters with other equipment under any circumstances. • If units do not work, check that AC adapters are plugged into working outlets. • When electricity is off (from a power failure, etc.), the Nursery Unit will operate on 3-AAA (1.5V-LR03) batteries. If the Power LED is not lit, turn the power off and then back on to the Nursery Unit. A green LED indicates that the batteries are fine. A red LED indicates that the batteries are low. If the LED does not light at all, then replace the batteries. The Parent Unit will operate if the rechargeable battery is charged. Selecting Channels • In case you are experiencing some interference, the channel on the Nursery Unit can be changed by pressing the Channel Button (labelled “ch”) on the side of the unit. The Parent Unit will automatically scan all of the available channels until it locks on to the Nursery Unit. If you are still experiencing interference, press the Channel Button on the side of the Nursery Unit up to 3 times until a good channel is found. 3 Low Battery Indication Parent Unit Low Battery Indication Parent Unit • When the battery is low in the Parent Unit, the LED bar on the side of the unit will change from green to red and you will hear a series of 3 audible beeps every 5 seconds. If operated too long on a low battery, you may also experience a poor signal and the loss connection LED on the front of the Parent Unit will illuminate red and you will begin to hear a continuous audible beep from the Parent Unit. •You may either turn off the unit, plug in the A/C adapter or place the unit in the docking station to recharge the batteries. Nursery Unit • When the battery is low in the Child Unit, the LED on the front of the unit will change from green to red. If operated too long on a low battery, you may also experience a poor signal from one or both of the Nursery Units. Under this circumstance, the loss connection LED (red) on the front of the Parent Unit may illuminate when the corresponding Nursery Unit is active and you will begin to hear a continuous audible beep from the Parent Unit. • You may either plug in the A/C adapter or replace the batteries. Out of Range Indicator • If the Parent Unit begins to lose signal from one or both of the Nursery Units, the loss connection LED (red) will illuminate when the corresponding Nursery Unit is active. Additionally, a continuous audible beep will be generated to warn the user that the connection to the Nursery Unit(s) has been lost. • Immediately move the Parent Unit closer to the Nursery Unit(s) to regain connection. • Once connection has been re-gained, the Loss Connection LED will turn off and the audible beep will stop. ***Note: It is not uncommon for the Parent Unit to occasionally lose and regain connection with the Nursery Unit in environments that have a significant amount of obstructions. First Time Use ***NOTE: It is very important that the steps below be followed f...