Évaluations - 5, GPA: 4.4
(
)
)
|
Facilité d'utilisation
13 CKS2235_032106.p65 13 21/3/2006, 11:00 RADIO AND BUZZER OPERATION You may also set one alarm for wake to radio and the other for wake to buzzer. Just set the ALM 1 and ALM 2 selector switches to the desired positions. SNOOZE ALARM After the alarm turns on in the morning you can use the Snooze function to grab a few more minutes sleep before the alarm sounds again. To activate the Snooze function you can press the SNOOZE (SLEEP OFF) button on the top cabinet. If you set WAKE TO BUZZER, you can simply wave your hand in front of the SNOOZE SENSOR on the front left panel. TOUCHLESS SNOOZE CONTROL (WAKE TO BUZZER Only) If you selected the WAKE TO BUZZER option you can activate the SNOOZE alarm without physically touching the SNOOZE button. When the buzzer alarm sounds in the morning, just wave your hand in front of the SNOOZE SENSOR on the front panel (see illustration) to activate the SNOOZE alarm. The Touchless Snooze Control works by detecting body heat. For best results your hand should be within 12 inches of the front panel. 14 CKS2235_032106.p65 14 21/3/2006, 11:00 SLEEP TO MUSIC TIMER You can program the sleep timer to play the radio for up to 90 minutes and then shut off automatically. 1.) Press the SLEEP button. The display will briefly show “10” and the radio will begin to play. After 10 minutes the radio will shut off automatically. Each time you press the SLEEP button the sleep timer will start at 10 minutes. This is the sleep timer default setting. 2.) To increase or decrease the amount of time that the radio will play before shutting off, hold the SLEEP button and press either the SET + or – button to change the display to the desired sleep time, up to a maximum of 90 minutes or a minimum of 2 minutes. Note: When you change the sleep timer from the 10 minute default setting to a different setting, the new setting becomes the default setting. Whenever you activate the sleep timer it will begin with your new default setting and count down to zero from that point. 3.) To cancel the sleep timer before it counts down to “00”and shut the radio ‘Off’ immediately, press the SNOOZE Bar. IMPORTANT: Remember that the station and volume settings you choose for the Sleep To Music operation are the same settings you will hear if you set the alarm for wake to radio the following morning. DIMMER CONTROL The DIMMER control was set to the HI (High) position at our factory. If you find the clock display is too bright in a darkened room, set the Dimmer control to the LO (Low) position. 15 CKS2235_032106.p65 15 21/3/2006, 11:00 16 CHANGING THE LITHIUM BATTERY Like all batteries, eventually the built in lithium battery will need to be replaced. A number of factors, such as, the length of time between the date the radio was manufactured and the date you plugged it in for the first time determine the amount of time before replacement. During this initial storage period, the lithium battery is supplying power to the SmartSet® computer memory. Once you plug the radio in, your household outlet supplies the power, and the battery is not being used. A fresh lithium battery can supply power to the SmartSet® computer for at least 3 years even if it is never connected to an AC power supply. If your radio was connected to your AC supply within a few months after it was manufactured, and you experience only the normal, nuisance type, short duration power interruptions, your battery may last for up to 5 years or even longer. When the battery power drops below a certain level, the LOW BATT indicator will ‘flash’. When you see this indicator, you should change the battery as soon as it is convenient for you to do so. To change the battery proceed as follows: 1.) Purchase a replacement 3V lithium battery wherever batteries are sold. The battery type is CR2430 or equivalent. 2.) Remove the battery from its package so it is ready to install. IMPORTANT: Leave the radio power cord connected to your AC outlet. This will provide power to the SmartSet® computer memory while the original lithium battery is removed. 3.) Turn the radio upside down and use a small screwdriver to remove the screws securing the battery holder to the cabinet. BE CAREFUL NOT TO LOSE THESE SMALL SCREWS! CKS2235_032106.p65 16 21/3/2006, 11:00 4.) Remove the original battery from the holder and insert the new battery into the holder the same way, observing the positive (+) direction. Slide the holder with the new battery back into the slot in the cabinet. 5.) Replace the screws that secure the battery holder in the cabinet. 6.) Turn the radio right side up and confirm that the LOW BATT indicator is ‘Off’. 7.) Save these instructions. You’ll have to do this again five to eight years from now! 17 CKS2235_032106.p65 17 21/3/2006, 11:00 RESETTING THE CLOCK AFTER A TOTAL MEMORY LOSS If you do not change the built in lithium battery within a reasonable period of time after you see the ‘flashing’LOW BATT warning indicator, the lithium battery may become exhausted and will n...