Évaluations - 1, GPA: 3
(
)
)
|
Facilité d'utilisation
wake up - cd track - selects CD wake track. CD MODE - selects CD mode. SET - enters clock and wake time setting mode. REV & FWD - set time and select CD track. SNOOZE - enters snooze mode where the alarm will quiet but sound again once the snooze period is over. ON - turns radio on and selects AUX input mode. Right View BAND - selects between AM and FM bands. TUNING - selects radio frequencies. Brightness Control Clock time and CD playback information are display on the display area at the front of the unit. Slide BRIGHTNESS switch on the left of the unit to HI (high) or LO (low) position to adjust the brightness. Selecting Radio Mode Press ON to switch on radio. Switching Band Slide the BAND switch on the right of the unit to select FM or AM band. Tuning the Radio Turn the TUNING knob on the right of the unit to adjust radio frequency. Built-In AFC The Built In Automatic Frequency Control (AFC) works only on FM. It helps reducing drift on FM reception and keeping the radio locked in on the FM station to which it is tuned. When tuning in FM stations, you may notice that the station you are tuning can be well-tuned on two or three nearby points on the dial. Always tune carefully at the loudest and clearest point. AM Antenna A built-in ferrite rod antenna eliminates the need for an outside antenna for AM reception. Rotating the unit slightly may improve reception of distant AM stations. Listening to Auxiliary Source 1. Connect your auxiliary source (e.g. mp3 player) to the AUX input jack on the left side of the unit. 2. Start playback from your auxiliary source. 3. Press ON to switch to listen to auxiliary source. The AUX indicator on the front will turn on. Press again to switch back to listen to the radio. Wake Function Tip: The unit equips with GRADU- WAKE feature, the alarm tone volume will increase gradually to its maximum in about 30 to 45 seconds. Turning Off the Wake Alarm, Radio or CD Press SNOOZE on the top of the unit. The wake alarm or radio will be switched off temporarily. The alarm, radio or CD will be on again when the snooze period is over. (see “SmartSnoozeTM Operation”) To turn off the wake alarm, radio or CD completely, press OFF. The wake alarm or radio will activate again the next day unless you switch off the Wake function (see “Switching off Wake Function”). SmartSnoozeTM Operation This operation allows extra sleep time after the wake function is on. The alarm will be off by pressing SNOOZE, NAP, SLEEP, REV or FWD until the snooze period is over. Snooze function can be used repeatedly up to 30 minutes (default: 9 minutes). After this, the wake function will turn off until the next day. Set the “quiet” period as follow: 1. Press and hold SNOOZE. 2. Press REV or FWD to set the quiet period. The time decrements or increments will follow by a faster rate when you press and hold the buttons. Switching Off Wake Function Press WK-1 or WK-2 repeatedly at the front of the unit until no wake mode icon shows on the display. Sleep Function In sleep mode, you can set the duration (up to 2 hours) before the radio or CD turn off automatically. 1. While listening to radio or CD, press and hold SLEEP at the front of the unit and use REV or FWD to set the duration up to 2 hours. The time decrements or increments will follow by a faster rate when you press and hold the buttons. Nap Function This function wakes you up after a short period of time (from 10 minutes to 2 hours). 1. Press NAP once at the front of the unit and while the NAP icon is flashing on the display, press REV or FWD to set the duration up to 2 hours (each press decreases or increases duration by 10 minutes). 2. The clock time shows after a few seconds if no button is pressed. NAP icon shows on the display to indicate the function is activated. 3. To check remaining nap time, press NAP once to show the time on the display briefly. 4. When the alarm sounds, press SNOOZE to switch it off. • To cancel the function before the nap time ends, press and hold NAP until no NAP icon shows on the display. Clock Wake Function Es importante leer este manual antes de usar por vez primera su euipo. Battery Back-Up Operation The power failure protection circuit will not operate unless battery is installed. When the battery backup functions, the digital display will not light, however, the wake function still occurs during the power interruption if remaining battery power is adequate. Normal operation will resume after AC power is restored so you will not have to reset the time or wake. Install battery as follow: 1. Remove battery compartment door (located at the bottom of the radio) by applying thumb pressure to the tab on battery door and then lift the door out and off the cabinet. 2. Connect a 9-volt battery (not supplied) to the connector plug. 3. Replace the compartment door. Left View BRIGHTNESS - selects display brightness between high and low. -VOLUME+ - adjusts volume. AUX IN - AUX input jack. Radio CD Player Listening to CD 1. Lift CD OPEN to o...