Évaluations - 5, GPA: 4.2
(
)
)
|
Facilité d'utilisation
• Attention should be drawn to the environmental aspects of battery disposal. • Minimum distances (2cm) should be kept around the apparatus for sufficient ventilations. • The ventilation should not be impeded by covering the ventilation opening with items, such as newspaper, tablecloths, curtains, etc. • The rating plate is located at the bottom cabinet of apparatus. Maintenance Clean the unit with a soft cloth, or a damp chamois leather. Never use solvents. The descriptions and characteristics in this owner’s manual are for the purpose of general reference only and not as a guarantee. In order to provide you with the highest quality product, we may make changes or modifications without prior notice. The English version serves as the final reference on all product and operational details should any discrepancies arise in other languages. Power failure indicator When external DC power is interrupted (disconnected) for a short period of time, both time and alarm settings will change (unless batteries are installed). After external DC power is restored (reconnected), the Digital Display will blink to indicate that power was interrupted and you should readjust the time and alarm settings. Plugging in for power Insert the connector of the AC/DC adpater to the power jack at the bottom of the unit. External AC/DC adaptor input power supply: 100-240V ~ 50/60Hz Note: Power is fed to the unit even when it is not functioning. To cut the power supply off, the power cable must be unplugged. Battery back-up operation This clock radio is equipped with a memory holding system that can be powered with 2 “AA” batteries (included). The power failure protection circuit will not operate unless battery is installed. When normal household power is interrupted, or AC line cord is unplugged, the batteries will power the clock radio to keep track of time and alarm settings programmed into memory. When the battery backup functions, the digital display will not light, however, the function of alarm still occurs during the power interruption if remaining battery power is adequate. Normal operation will resume after AC power is restored so you will not have to reset the time or the alarm. Install battery as follow: 1. Remove battery compartment door (located at the bottom of the radio) by applying thumb pressure to the tab on battery door and then lift the door out and off the cabinet. 2. Insert 2 AA batteries (included). 3. Replace the compartment door. Note: we recommend that you replace the batteries every 2-3 years. Turns off the unit (standby mode) Front view Universal dock for iPod® (push to open or close) Selects radio, USB or iPod mode Display Selects random playback mode Selects repeat playback mode Skips to the previous or next file, searches backward or forward Turns off the wake function momentarily, turns off the sleep funtion USB connector Top view Activates wake time 1 Activates wake time 2 Refer to “Sleep function” Refer to “NAP function” Press SET at the center to select adjusting the clock time, wake time 1 or wake time 2. Rotate the knob to adjust the clock time, wake time 1 or wake time 2. Selects the radio frequency Side views Selects the radio band Adjusts the volume Selects the display brightness Bottom view Time zone selector (refer to “Clock”) Daylight saving time button (refer to “Clock”) Battery compartment (refer to “Battery back-up operation”) Setting clock In case the memory holding batteries are accidentally removed, set the clock manually as below: 1. Press SET on the top of the unit until the clock setting icon flashes on the display. 2. Rotate the knob on the top of the unit to set the clock time. The time decrements or increments follows by a faster rate when you rotate and hold the knob. The clock setting icon flashes when you are setting the time. AM or PM icon also shows beside the time. 3. To save and exit the clock setting, wait for about 5 seconds or press SET until the clock setting , WAKE 1 or WAKE 2 icon is off. The clock time is now set. Auto clock set You do not have to set the clock time as a built-in automatic time set system is equipped in this clock powered by 3V (2 AA batteries, included and installed). All you have to do is to plug this clock for power and current time will be shown automatically after setting the time zone and daylight saving time (read below). However, the batteries can also be exhausted and we recommend that you replace the batteries every 2-3 years. Setting time zone Slide the time zone selector at the bottom of the unit to Eastern, Central, Mountain or Pacific time zone (refer to the maps on the right). Daylight saving time Press and hold the Daylight Saving Time button at the bottom of the unit to turn on/ off in areas observing/ not observing such time change. The icon shows on the display when daylight saving time is active. WARNING: Avoid playing with these buttons when setting clock or wake time. Canadian time zones US time zones Listening to the radio 1. Pre...
Ce manuel est également adapté pour les modèles :récepteurs radio - RP5500I (447.32 kb)