Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
2 Press BAND repeatedly to select the desired band. 3 Use TUNING + or – to tune in to the desired station. The FM channel step is set to 0.05 MHz* and the AM (MW)/LW channel step is set to 9 kHz. * The FM frequency display is raised or lowered by a step of 0.1 MHz. For example, frequency 88.00 and 88.05 MHz is displayed as “88.0 MHz.” Two short beeps sound when the minimum frequency of each band is received during tuning. reception conditions The display shows the frequency for a few seconds and then changes back to the current time. For the radio alarm, preset the station to be used as the alarm onto preset 1 button. To change a preset station Tune in manually to the station you want to store and hold down the preset button until you hear two short beeps. The previously stored station will be replaced by the new one. Tuning in to a preset station 1 Press RADIO ON to turn on the radio. 2 Press STATION•SELECT/PRESET where the desired station is stored. 3 Adjust volume using VOL. After a few seconds, the display will return to the current time but the preset button number will remain. Setting the Alarm You can choose from two types of alarm, Radio (A) or Buzzer (B). The alarm will come on at the same time everyday. The factory setting alarm time for the radio (A) and buzzer (B) is 0:00. Notes • Set the current time before setting the alarm. • Radio reception is interrupted while the alarm time is being set. To Use the Radio (A) Alarm You can use the station preset onto the “Preset 1 Button” (WAKE UP STATION) as the alarm (see “Preset Tuning”). Preset a station onto preset 1 button. 1 Set the alarm setting dial to ALARM TIME SET A. After one beep, indicator A flashes. 2 Press CLOCK + or – to select the desired time. When CLOCK + or – is held down, the displayed time initially changes in oneminute steps, then after a few seconds switches to ten-minute steps. 3 Set the alarm setting dial to ALARM MODE RADIO A. Indicator A lights up. When the alarm comes on at the preset time, indicator A flashes and the radio station that is preset with the preset 1 button comes on. The unit switches off automatically after about 60 minutes. To Use the Buzzer (B) Alarm 1 Set the alarm setting dial to ALARM TIME SET B. After one beep, indicator B flashes. 2 Press CLOCK + or – to select the desired time. When CLOCK + or – is held down, the displayed time initially changes in oneminute steps, then after a few seconds switches to ten-minute steps. 3 Set the alarm setting dial to ALARM MODE BUZZER B. Indicator B lights up. When the alarm comes on at the preset time, indicator B flashes and the beep sounds. The beeping becomes more rapid after every few seconds in five progressive stages. The unit switches off automatically after about 60 minutes. To Use the Radio (A) and Buzzer (B) Alarm 1 Set both alarm times for ALARM TIME SET A/B. (see above) . 2 Set the alarm setting dial to ALARM MODE A+B. Indicators A and B light up. If the same alarm time is set for both (A) and (B), (A) takes priority. To Check the Alarm Time Press ALARM TIME CHECK. The display shows the alarm time for a few seconds and then returns to show the current time. When the alarm setting dial is set to either ALARM MODE OFF or A + B, the alarm time in RADIO A and then BUZZER B appears in the display. reception conditions .. .... .. Screw (not supplied) 4 Adjust volume using VOL. • To turn off the radio, press RADIO OFF. • To improve reception FM: Extend the FM wire antenna fully to increase reception sensitivity. AM(MW)/LW: Rotate the unit horizontally for optimum reception. A ferrite bar is built in to the unit. Do not operate the unit over a steel desk or metal surface, as this may lead to interference of reception. • To check the station being received, press TUNING + or – lightly. The display shows the band and frequency for a few seconds and then changes back to the current time. • If the radio alarm comes on while the radio is on, the unit switches to the station on WAKE UP STATION (preset 1 button). Preset Tuning You can preset up to five stations for one-touch tuning; one for each of the preset buttons 1 to 5. Presetting a station Example: To preset AM 1 260 kHz onto preset 2 button. 1 Press RADIO ON to turn on the radio. 2 Tune in to the station you want to preset. (See “Manual Tuning”.) 3 Hold down the desired STATION•SELECT/PRESET button (in this case, 2) until you hear two short beeps. Indicator Indicateur Alarm setting dial Molette de reglage de l’alarme FM wire antenna Antenna fil FM VOL Radio-controlled clock antenna Antenne d’horloge controlee par la radio AC power cord Cordon d’alimentation secteur ALARM TIME SET A/B ALARM MODE OFF / RADIO A / BUZZER B / A+B To Doze for a Few More Minutes Press SNOOZE/DATE/SLEEP OFF. The radio or buzzer turns off but will automatically come on again after about 8 minutes. Every time you press SNOOZE/DATE/SLEEP OFF, the snooze time changes as follows: The display shows the snooze time for a few seconds and returns to...
Ce manuel est également adapté pour les modèles :récepteurs radio - ICF-C255RC (435.15 kb)