Évaluations - 3, GPA: 3
(
)
)
|
Facilité d'utilisation
Example: The following display appears when you preset FM 105.8 MHz to preset number 1 for FM. . The display shows the frequency for about 10 seconds, and then returns to the current time. To preset another station, repeat these steps. Note If you try to store another station with the same preset number, the previously stored station will be replaced. –Auto preset tuning 1 Press RADIO BAND to turn on the radio and select the AM or FM band. 2 Press and hold RADIO BAND until “Auto” appears in the display. 3 Press MEMORY/DISPLAY. The unit automatically presets the available channels in order. Tuning in to a station 1 Press RADIO BAND to turn on the radio and select the AM or FM band. 2 Press PRESET + or – to select the desired preset number. 3 Adjust the volume using VOLUME + or –. Improving the reception FM: Extend the FM wire antenna fully to increase reception sensitivity. AM: Connect the supplied AM loop antenna to the unit. Rotate the antenna horizontally for optimum reception. Tip If the FM broadcast is noisy, press MODE to turn off “ST” in the display. The radio becomes clearer although the sound becomes monaural. Notes on radio reception . Keep digital music players or mobile phones away from the AM loop antenna or the FM antenna, as this may lead to interference of reception. . When you are listening to the radio with an iPhone connected to the unit, interference with radio reception may occur. . When you are listening to the radio while charging an iPod, interference with radio reception may occur. Playing an iPod You can enjoy audio from iPod by connecting to this unit. To use an iPod, refer to the user’s guide of your iPod. Notes . When inserting an iPod into the unit, be sure to use the universal dock adapter supplied with your iPod or commercially available from Apple Inc. . If you are using an iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G or iPhone, attach the supplied universal dock adapter for iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G or iPhone before connecting. The adapter number, ., . or ., is shown on the bottom-rear of the supplied universal dock adapters. . is for the iPhone, . is for the iPhone 3GS & iPhone 3G and . is for the iPhone 4S & iPhone 4. Check the adapter number before use. . The connector of the unit is exclusively for use with iPod. When you use a device that does not match the connector, connect it to the AUDIO IN terminal of this unit with the supplied audio connecting cable. . Sony cannot accept responsibility in the event that data recorded on an iPod is lost or damaged when using an iPod connected to this unit. . For details of environmental conditions for operating your iPod, check the website of Apple Inc. 1 Push OPEN to slide out the Docking Tray. 2 Attach the correct universal dock adapter to the connector of the unit, and place the iPod/iPhone to the connector. 3 Press iPod & iPhone .. The iPod begins to play automatically. You can operate the connected iPod by this unit or the buttons on iPod. 4 Adjust the volume using VOLUME + or –. To Press Turn off the iPod OFF, or press and hold iPod & iPhone . Pause playback iPod & iPhone . To resume play, press it again. Go to the next track . Go back to the previous track .* Locate a point while listening to the sound . (forward) or . (backward) while playing and hold it until you find the point. Locate a point while observing the display . (forward) or . (backward) in pause and hold it until you find the point. Go back to the previous menu MENU** Select a menu item or a track for playback ./.** Execute the selected menu or begin playback ENTER** * During playback, this operation goes back to the beginning of the current track. To go back to the previous track, press twice. ** These operations are available only when using the supplied remote commander. Notes . When placing or removing the iPod, hold the iPod at the same angle as that of the connector on this unit and do not twist or bend the iPod to prevent connector damage. . Do not carry the unit with an iPod set on the connector. Doing so may cause a malfunction. . When placing or removing the iPod, brace the unit with one hand and take care not to press the controls of the iPod by mistake. . Before disconnecting the iPod, pause playback. To use the unit as a battery charger You can use the unit as a battery charger. The charging begins when the iPod is placed on the connector. The charging status appears in the display of iPod. For details, see the user’s guide of your iPod. On copyrights iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the us...