Log:
Évaluations - 1, GPA: 4 ( )

Instructions Roberts Radio, Modèle CR9932

Fabricant : Roberts Radio
Taille : 373.07 kb
Nom Fichier : cr9932.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


4. Whilst holding down the Time Set button press the Hour, or Minute buttons to set the time. Release the buttons when the correct time is reached. The clock uses a 12 hour display with a PM indicator. Ensure that the correct 12 hour cycle is selected. Listening 1. Turn on the radio Function switch to the 'On ' position. The LED dial pointer will light up indicating radio is switched on. 2. Select the required waveband using Waveband selector switch. 3. Tune in to the desired station by rotating the Tuning control. The station frequency is indicated by the LED dial pointer. The Wire aerial located on the rear of your clock radio is for FM reception. The wire should be fully extended and positioned for optimum reception. For MW and LW reception there is a built-in ferrite aerial. Rotate your clock radio to the position giving best reception. 4. Adjust the volume by rotating the Volume control. 5. The radio can be switched off by sliding the Function switch to the 'Off ' position. If you need any further advice, please call our Technical Helpline on : 020 8758 0338 (Mon-Fri) Alarm The alarm can be Setting alarm time 1. Press and hold down the Alarm/Off button. 2. Whilst holding down the Alarm/Off button press the Hour, or Minute buttons to set the time. Release the buttons when correct alarm time is reached. The clock uses with a PM indicator. Ensure that the correct 12 hour cycle is selected. Checking the alarm time 1. To check alarm time, press and hold down the Alarm/Off button the display will show the alarm time Setting the 1. Set the alarm time Function switch to the ' Buzz' position. The Alarm indicator will light. The alarm will sound every To turn off the alarm until the next Alarm/Off button. To turn off the alarms permanently set the Function selector to the ' Off' position. Setting the alarms to wake to radio 1. Set the alarm time as previously described. Set the Function switch to the ' Auto' position. The Alarm indicator will light. Ensure that the volume is set to the correct level and the desired station is tuned in. The alarm will sound every day at the preset time for 59 minutes. To turn off the alarm until the next day press the Alarm/Off button. To turn off the alarms permanently set the Function selector to the ' Off' position. If you need any further advice, please call our Technical Helpline on : 020 8758 0338 (Mon-Fri) Snooze control The radio or buzzer Snooze Light button. This sequence is sounding. Sleep timer The radio can be set to turn off after a preset time has Press and hold down the Sleep button until the desired time is reached (maximum 59 minutes in 1 minute steps). The radio will switch the sleep time has elapsed. To cancel the sleep function before the preset time has expired, press the Alarm/Off button. Dimmer Switch The Dimmer switch located on the left side of your clock radio will allow you to adjust the intensity of the clock display to suit room brightness. Headphones A Headphone Socket (3.5mm) is provided headphones or an the internal loudspeaker. Night light Press the Snooze button once to turn on the night light. Press again to turn it off. The night-light will provide a warm glow to allow movement around the room safely. It is not intended as a reading light. If you need any further advice, please call our Technical Helpline on : 020 8758 0338 (Mon-Fri) General Do not allow this that the FM band be of quality and freedom than on the MW or LW bands. Mains supply The CR9932 will operate from a supply AC 230volts, 50Hz only. For your convenience this product is fitted with a fuse of the appropriate rating. suitable for your socket outlet, it should be plug top, the terminal screws, and removing The correct style of plug to suit your household rated fuse should be fitted. IF IN DOUBT - CONSULT A QUALIFIED ELECTRICIAN IMPORTANT. DO NOT make any connection to the larger terminal which is marked with the letter E or by the safety earth symbol or coloured Green or Green-and-yellow. The wires in the mains lead are coloured in accordance with the following codes : BLUE - NEUTRAL BROWN - LIVE As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire coloured BLUE must be connected to the terminal marked N or coloured BLACK. The wire coloured BROWN must be connected to the terminal marked L or coloured RED. Fuse This apparatus must be protected fuse (BS1362) in plug (BS1363). If another the plug, adaptor or distribution IF IN DOUBT - CONSULT A QUALIFIED ELECTRICIAN. Back-up Battery (not necessary Slide the battery cover catch in the Remove the battery cover. Fit a 9 volt IEC size 6LR61(6F22,PP3) battery into the compartment. Replace the battery cover. The time and alarm settings will be retained of the AC mains supply. The LED display will not be operational. The display will be extinguished to conserve battery life. (Underside) Specifications Circuit FeaturesPower Requirements Loudspeaker 75mm diamete...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories